Bedienungsanleitung Scheppach BS2000 Primaster (Seite 23 von 46) (Deutsch, Englisch, Französisch)

782174

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

23GB

The manufacturer shall not be liable for any changes

made to the machine nor for any damage resulting

from such changes.

Even when the machine is used as prescribed it is

still impossible to eliminate certain residual risk fac-

tors. The following hazards may arise in connection

with the machine’s construction and design:

• Damage to hearing if ear-muffs are not used as

necessary.

• Harmful emissions of wood dust when used in

closed rooms.

• Contact with the blade in the uncovered cutting

zone.

• Injuries (cuts) when changing the blade.

• Injury from catapulted workpieces or parts of work-

pieces.

• Crushed ngers.

• Kickback.

• Tilting of the workpiece due to inadequate support.

• Touching the blade.

• Catapulting of pieces of timber and workpieces.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial ap-

plications. Our warranty will be voided if the machine

is used in commercial, trade or industrial businesses

or for equivalent purposes.

5. General safety information

Attention! The following basic safety measures must

be observed when using electric tools for protection

against electric shock, and the risk of injury and re.

Read all these notices before using the electric tool

and keep the safety instructions for later reference.

Safe work

1 Keep the work area orderly

–Disorder in the work area can lead to accidents.

2 Take environmental inuences into account

–Do not expose electric tools to rain.

–Do not use electric tools in a damp or wet en-

vironment.

–Make sure that the work area is well-illuminated.

–Do not use electric tools where there is a risk of

re or explosion.

3 Protect yourself from electric shock

–Avoid physical contact with earthed parts (e.g.

pipes, radiators, electric ranges, cooling units).

4 Keep children away

–Do not allow other persons to touch the equip-

ment or cable, keep them away from your work

area.

5 Securely store unused electric tools

–Unused electric tools should be stored in a dry,

elevated or closed location out of the reach of

children.

6 Do not overload your electric tool

–They work better and more safely in the speci-

ed output range.

7 Use the correct electric tool

–Do not use low-output electric tools for heavy

work.

–Do not use the electric tool for purposes for

which it is not intended. For example, do not

use handheld circular saws for the cutting of

branches or logs.

–Do not use the electric tool to cut rewood.

8 Wear suitable clothing

–Do not wear wide clothing or jewellery, which

can become entangled in moving parts.

–When working outdoors, anti-slip footwear is

recommended.

–Tie long hair back in a hair net.

9 Use protective equipment

–Wear protective goggles.

–Wear a mask when carrying out dust-creating

work.

10 Connect the dust extraction device if you will be

processing wood, materials similar to wood, or

plastics.

–If connections for dust extraction and a collect-

ing device are present, make sure that they are

connected and used properly.

–When processing wood, materials similar to

wood, and plastics. operation in enclosed spac-

es is only permitted with the use of a suitable

extraction system.

11 Secure the workpiece

–Use the clamping devices or a vice to hold the

workpiece in place. In this manner, it is held

more securely than with your hand.

–An additional support is necessary for long

workpieces (table, trestle, etc.) in order to pre-

vent the machine from tipping over.

–Always press the workpiece rmly against

the working plate and stop in order to prevent

bouncing and twisting of the workpiece.

12 Avoid abnormal posture

–Make sure that you have secure footing and

always maintain your balance.

–Avoid awkward hand positions in which a sud-

den slip could cause one or both hands to come

into contact with the saw blade.

13 Take care of your tools

–Keep cutting tools sharp and clean in order to

be able to work better and more safely.

–Follow the instructions for lubrication and for

tool replacement.

–Check the connection cable of the electric tool

regularly and have it replaced by a recognised

specialist when damaged.

–Check extension cables regularly and replace

them when damaged.

–Keep the handle dry, clean and free of oil and

grease.

14 Pull the plug out of the outlet

–Never remove loose splinters, chips or jammed

wood pieces from the running saw blade.

–During non-use of the electric tool or prior to

maintenance and when replacing tools such as

saw blades, bits, milling heads.

–When the saw blade is blocked due to abnormal

feed force during cutting, turn the machine off

and disconnect it from power supply. Remove

the work piece and ensure that the saw blade

runs free. Turn the machine on and start new

cutting operation with reduced feed force.

15 Do not leave a tool key inserted

–Before switching on, make sure that keys and

adjusting tools are removed.

16 Avoid inadvertent starting

–Make sure that the switch is switched off when

plugging the plug into an outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BS2000 Primaster Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info