Bedienungsanleitung Scheppach BS2000 Primaster (Seite 24 von 46) (Deutsch, Englisch, Französisch)

782174

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

24 GB

17 Use extension cables for outdoors

–Only use approved and appropriately identied

extension cables for use outdoors.

–Only use cable reels in the unrolled state.

18 Remain attentive

–Pay attention to what you are doing. Remain

sensible when working. Do not use the electric

tool when you are distracted.

19 Check the electric tool for potential damage

–Protective devices and other parts must be

carefully inspected to ensure that they are fault-

free and function as intended prior to continued

use of the electric tool.

–Check whether the moving parts function fault-

lessly and do not jam or whether parts are dam-

aged. All parts must be correctly mounted and

all conditions must be fullled to ensure fault-

free operation of the electric tool.

–The moving protective hood may not be xed

in the open position.

–Damaged protective devices and parts must be

properly repaired or replaced by a recognised

workshop, insofar as nothing different is speci-

ed in the operating manual.

–Damaged switches must be replaced at a cus-

tomer service workshop.

–Do not use any faulty or damaged connection

cables.

–Do not use any electric tool on which the switch

cannot be switched on and off.

20 ATTENTION!

–The use of other insertion tools and other ac-

cessories can entail a risk of injury.

21 Have your electric tool repaired by a qualied

electrician

–This electric tool conforms to the applicable

safety regulations. Repairs may only be per-

formed by an electrician using original spare

parts. Otherwise accidents can occur.

22 Do not use the cable for purposes for which it is

not intended Do not use the cable to pull the plug

out of the outlet. Protect the cable from heat, oil

and sharp edges.

Additional safety instructions

• Wear safety gloves whenever you carry out any

maintenance work on the blade!

• When cutting round or irregularly shaped wood,

use a device to stop the workpiece from twisting.

• When cutting boards in upright position, use a

device to prevent kick-back.

• A dust extraction system designed for an air ve-

locity of 20 m/s should be connected in order to

comply with woodworking dust emission values

and to ensure reliable operation.

• Give these safety regulations to all persons who

work on the machine.

• Do not use this saw to cut re wood.

• The machine is equipped with a safety switch to

prevent it being switched on again accidentally

after a power failure.

• Before you use the machine for the rst time,

check that the voltage marked on the rating plate

is the same as your mains voltage.

• If you use a cable reel, the complete cable has

to be pulled off the reel.

• Persons working on the machine should not be

distracted.

• Note the direction of rotation of the motor and

blade.

• Never dismantle the machineʼs safety devices

or put them out of operation.

• Never cut workpieces which are too small to

hold securely in your hand.

• Never remove loose splinters, chips or jammed

pieces of wood when the saw blade is running.

• It is imperative to observe the accident preven-

tion regulations in force in your area as well as

all other generally recognized rules of safety.

• Note the information published by your profes-

sional associations.

• Adjustable protective devices have to be adjust-

ed as close as possible to the workpiece.

• Important! Support long workpieces (e.g. with

a roller table) to prevent them sagging at the

end of a cut.

• Make sure the blade guard (3) is in its lower po-

sition when the saw is being transported.

• Safety guards are not to be used to move or mis-

use the machine.

• Blades that are misshapen or damaged in any

way must not be used.

• If the table insert is worn, replace it.

• Never operate the machine if either the door pro-

tecting the blade or the detachable safety device

are open.

• Ensure that the choice of blade and the selected

speed are suitable for the material to be cut.

• Do not begin cleaning the blade until it has come

to a complete standstill.

• For straight cuts of small workpieces against the

longitudinal limit stop the push stick has to be

used.

• The bandsaw blade guard should be in its low-

est position close to the bench during transport.

• For miter cuts when the table is tilted, the par-

allel stop must be positioned on the lower part

of the table.

• When cutting round timber, use a suitable hold-

ing device to prevent the workpiece turning.

• Never use guards to lift or transport items.

• Ensure that the bandsaw blade guards are used

and correctly adjusted.

• Keep your hands a safety distance away from

the bandsaw blade. Use a push stick for nar-

row cuts.

• The push stick has to be stored on the intended

device, so that it can be reached from normal

working position and is always ready to be used.

• In the normal operating position the operator is

in front of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BS2000 Primaster Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info