Bedienungsanleitung Scheppach BS3000 Primaster (Seite 24 von 44) (Deutsch, Englisch, Französisch)

782175

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

24 GB

• Before you connect the machine to the power

supply, make sure the data on the rating plate is

the same as that for your mains.

Assembly tools

1 engineer’s wrench SW 10/13

8.1 Mounting the base (Fig. 2+3)

Installation parts:

• 4 stand feet (A)

• stand braces below (B): 2 x long + 2 x short

• stand braces above (C): 2 x long + 2 x short

• 4 rubber feet (D), 4 washer 8, 4 nuts M8

• Mounting parts (24 carriage bolts M8x16, 4 hex

screws M8x45, 32 washer 8, 28 nuts M8)

Hand-tighten all screws lightly during the installation.

• Place the 4 rubber feet on the stand feet.

• Attach one stand brace below (B) each with 2

screws M8 x 16, 2 washer and 2 nuts to the stand

feet (A).

• Mount the frame struts above (C), each with 4 car-

riage bolts M8 x 16, 4 washers and 4 nuts on the

frame feet (A) as shown in Fig. 3.

• Place a cardboard box behind the machine and

then carefully tip the machine backward until the

machine rests on its housing.

• Place the previously assembled frame (Fig. 2) un-

der the base plate (E) of the band saw; screw it into

place by hand with 4 hex bolts M8x45, 8 washers,

4 circlips and 4 hex nuts. (Fig. 3)

• Set the machine with the base on a level surface

and tighten all the screws and nuts rmly.

8.2 Assembling the work table, (Fig. 4 - 6)

• Lay the table insert (a) in the recess in the work

table intended for this (Fig. 4). (To replace, disas-

semble the work table in reverse order.)

• Place the band saw blade through the slot on the

machine table. Place the machine table on the table

guide so that the xing screw (b) ts through the

bracket (c).

• Screw the machine table tight with the wing nut (E).

• Check that the bandsaw blade runs freely and does

not touch the table.

• Using the adjustment screw (F) to ad-

just the table to a right-angle.

– Use a set square –

• Counter the adjustment screw (F) and tighten the

wing nut (E).

• Set the scale pointer (G) to 0.

• Adjust the angle scale (I):

• By loosening the screws (H) and shifting

the angle scale (I) until the scale pointer (G)

points to 0. Fix screws.

8.3 Assembly of the length end stop (Fig. 7+8)

• Turn the four knurled screws (J), each with a at

washer, roughly 5 mm into the table surface (Fig. 7)

• Place the guidance tube so that it touches the table

and tighten the four knurled screws (J).

• Now, put the length end stop (5) on the guidance

pipe, to the left of the saw blade, and clamp it tightly.

The end stop pipe should now be parallel to the

table groove.

8.4 Setting the number of revolutions

(Fig.10+11+11.1)

Pull the mains plug!

• Open lower guard.

• Release the belt with the tension handle (10).

• Put the belt into the desired position. (L1 or L2).

• Retension the belt with the tension handle (10).

• Close the lower guard.

Rpm range:

Rpm stage 1 360 m/min.

For processing hardwood, materials similar to hard-

wood and for ne cuts.

Rpm stage 2 720 m/min.

For processing softwoods and for less ne cuts.

8.5 Sawblade guiding (Fig. 12)

The sawblade guiding (4) is adjusted with the xing

button (11).

The upper sawblade guiding can be set from 0 to 175

mm work piece height.

A clearance as small as possible to the work piece

ensures an optimum sawblade guiding and safe

working.

Back pressure bearings (Fig. 13+14)

The back pressure bearings (d) accept the feed pres-

sure of the work piece. Set the upper and lower back

pressure bearing in such a way that it slightly touch-

es the sawblade back. Tighten the screws (e). The

distance should be 0.5 mm.

Upper guide rollers (Fig. 13)

Set the upper guide rollers (f) to the corresponding

sawblade width. The front edges of the guide roll-

ers must not exceed the tooth base of the sawblade.

When the guide rollers slightly touch the sawblade,

tighten the screws (e).

Lower guide ngers (Fig. 14)

Set the lower guide ngers (g) to the corresponding

sawblade width. The front edges of the guide ngers

must not exceed the tooth base of the sawblade.

When the guide ngers slightly touch the sawblade,

tighten the set screws (h).

The sawblade must not jam!

8.6 Sawblade changing(Fig. 8-15)

Attention: Pull the mains plug!

Attention!

Wear protective gloves when changing the saw

blade! Risk of injury!

• Loosen the four knurled screws on the guide rail

for the lengthwise aligning stop. (Fig. 7)

• Remove the guide rail. (Fig. 8)

• Open the saw band guard, top and bottom.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BS3000 Primaster Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info