Bedienungsanleitung Scheppach BS3000 Primaster (Seite 22 von 44) (Deutsch, Englisch, Französisch)

782175

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

22 GB

12 Avoid abnormal posture

–Make sure that you have secure footing and

always maintain your balance.

–Avoid awkward hand positions in which a sud-

den slip could cause one or both hands to come

into contact with the saw blade.

13 Take care of your tools

–Keep cutting tools sharp and clean in order to

be able to work better and more safely.

–Follow the instructions for lubrication and for

tool replacement.

–Check the connection cable of the electric tool

regularly and have it replaced by a recognised

specialist when damaged.

–Check extension cables regularly and replace

them when damaged.

–Keep the handle dry, clean and free of oil and

grease.

14 Pull the plug out of the outlet

–Never remove loose splinters, chips or jammed

wood pieces from the running saw blade.

–During non-use of the electric tool or prior to

maintenance and when replacing tools such as

saw blades, bits, milling heads.

–When the saw blade is blocked due to abnormal

feed force during cutting, turn the machine off

and disconnect it from power supply. Remove

the work piece and ensure that the saw blade

runs free. Turn the machine on and start new

cutting operation with reduced feed force.

15 Do not leave a tool key inserted

–Before switching on, make sure that keys and

adjusting tools are removed.

16 Avoid inadvertent starting

–Make sure that the switch is switched off when

plugging the plug into an outlet.

17 Use extension cables for outdoors

–Only use approved and appropriately identied

extension cables for use outdoors.

–Only use cable reels in the unrolled state.

18 Remain attentive

–Pay attention to what you are doing. Remain

sensible when working. Do not use the electric

tool when you are distracted.

19 Check the electric tool for potential damage

–Protective devices and other parts must be

carefully inspected to ensure that they are fault-

free and function as intended prior to continued

use of the electric tool.

–Check whether the moving parts function fault-

lessly and do not jam or whether parts are dam-

aged. All parts must be correctly mounted and

all conditions must be fullled to ensure fault-

free operation of the electric tool.

–The moving protective hood may not be xed

in the open position.

–Damaged protective devices and parts must be

properly repaired or replaced by a recognised

workshop, insofar as nothing different is speci-

ed in the operating manual.

–Damaged switches must be replaced at a cus-

tomer service workshop.

–Do not use any faulty or damaged connection

cables.

–Do not use any electric tool on which the switch

cannot be switched on and off.

20 Attention!

–The use of other insertion tools and other ac-

cessories can entail a risk of injury.

21 Have your electric tool repaired by a qualied

electrician

–This electric tool conforms to the applicable

safety regulations. Repairs may only be per-

formed by an electrician using original spare

parts. Otherwise accidents can occur.

22 Do not use the cable for purposes for which it is

not intended Do not use the cable to pull the plug

out of the outlet. Protect the cable from heat, oil

and sharp edges.

Additional safety instructions

• Wear safety gloves whenever you carry out any

maintenance work on the blade!

• When cutting round or irregularly shaped wood, use

a device to stop the workpiece from twisting.

• When cutting boards in upright position, use a de-

vice to prevent kick-back.

• A dust extraction system designed for an air velocity

of 20 m/s should be connected in order to comply

with woodworking dust emission values and to en-

sure reliable operation.

• Give these safety regulations to all persons who

work on the machine.

• Do not use this saw to cut re wood.

• The machine is equipped with a safety switch to

prevent it being switched on again accidentally af-

ter a power failure.

• Before you use the machine for the rst time, check

that the voltage marked on the rating plate is the

same as your mains voltage.

• If you use a cable reel, the complete cable has to

be pulled off the reel.

• Persons working on the machine should not be dis-

tracted.

• Note the direction of rotation of the motor and blade.

• Never dismantle the machineʼs safety devices or put

them out of operation.

• Never cut workpieces which are too small to hold

securely in your hand.

• Never remove loose splinters, chips or jammed

pieces of wood when the saw blade is running.

• It is imperative to observe the accident prevention

regulations in force in your area as well as all other

generally recognized rules of safety.

• Note the information published by your professional

associations.

• Adjustable protective devices have to be adjusted

as close as possible to the workpiece.

• Important! Support long workpieces (e.g. with a roll-

er table) to prevent them sagging at the end of a cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BS3000 Primaster Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info