Bedienungsanleitung Scheppach CSD40-20Li (Seite 23 von 88) (Deutsch, Englisch, Französisch, Polnisch)

782591

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

23 | GB

be opened simply by turning it . After you have in-

serted the required bit and xed it in place by turning

the chuck , you can immediately continue working.

The spindle lock releases itself automatically when

the motor is started (by operation of the ON / OFF

switch 3 ).

Torque pre-selection

You can adjust the torque by using 14 torque prese-

lection.

Select a low setting for small screws, soft workma-

terial.

Select a high setting for large screws, hard work ma-

terials and for the extraction of screws.

For drilling, push the selector to the setting for drill-

ing, in that you adjust the torque pre-selector

to the position .

For drilling tasks, also push the gear selector switch

1 to the front (Position: 2).

2 Gear Drive

CAUTION! Move the gear selector switch 1 only after

the device has come to a standstill.

Failure to observe this advice may result in damage

to the device.

In the rst gear (Gear selector switch 1 in Position: 1)

A speed of up to approx. 400 rpm can be achieved

and a high torque. This setting is intended for use

with all screwing tasks and for accessories (see ex-

ample Fig. B).

In the second gear (Gear selector switch 1 in Posi-

tion: 2)

It achieves a speed of up to approx. 1400 rpm, for

the carrying out of drilling tasks (see example Fig. A).

Preparing the tool for use

Switching On /Off

Switching on:

To start the appliance squeeze on the ON / OFF

switch 3 and then keep it pressed down. The LED

working light 12 comes on with a slightly or fully

pressed ON /OFF switch 3 and illuminates the work-

ing area in poor lighting conditions.

Switching off:

To stop the appliance, release the ON

Adjusting the speed

The ON / OFF switch 3 has a variable speed control

device. Slight pressure on the ON / OFF

switch 3 will cause the rotation speed to slow down.

With increased pressure, the rotational speed will in-

crease.

Note: The integrated engine brake means that the

device will come to a fast standstill.

Switching direction of rotation

To switch the direction of rotation, push the direction

of rotation switch 2 to either the

right or to the left.

Tips and Tricks

Before you use the appliance, check to see that the

screw or drill bit is properly tted, i.e.

located centrally in the chuck.

Screw bits are designated with their dimensions and

their shape. If you are unsure, always try

the particular screw bit out to see whether it sits in

the screw head without any free play.

Torque:

Smaller screws and bits in particular can be easily

damaged if you adjust the appliance with too high a

torque and/or rotation speed.

Hard screwdriving conditions (into metal):

Particularly high torques can occur, for example with

metal screws tightened by socket tool bits.

Select a lower rotation speed.

Soft screwdriving conditions (e.g. into soft wood):

You should also select a low speed in order not to

damage the wood workpiece surface through con-

tact with the metal screw head.

Use a countersinker.

When drilling into wood, metal and other materials,

take note of the following advice:

With small diameter drill bits use a high drill speed.

For large diameter drill bits, use a low drill speed.

For hard materials, select a low drill speed.

For soft materials, select a high drill speed.

Secure or x down the workpiece (if possible) in a

clamp or vice.

Mark the intended position of the hole with a centre

punch or a nail and select a low drill speed

for drilling.

Take the rotating drill bit out of the hole frequently so

that swarf or drill dust can be re-moved and

the hole and tool is ventilated.

Drilling in metal:

Use a metal drill bit (HSS). For the best results, you

should cool the bit with oil. Metal drill bits

can also be used to drill into plastic.

Drilling in stone:

Use a circular shafted masonry drill bit with a hard-

ened metal tip.

Drilling in wood:

Normally you should use a wood drill with a centring

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach CSD40-20Li Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info