Bedienungsanleitung Scheppach DECO-XLS (Seite 31 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

781462

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

www.scheppach.com GB | 31

6. Put the table insert (26) back.

NOTE

The left side features a storage box (9), which enables

you to stow replacement saw blades and the hexagon

wrench.

8.2 Checking the saw blade tension

WARNING

Check the blade tension regularly and after insert-

ing a saw blade.

Tension the saw blade after assembly by pressing

down on the tension lever (11).

If the blade tension is too low or too high, proceed as

follows:

• Fold the tension lever (11) upwards.

• Turn the tension lever (11) clockwise to increase the

tension and anti-clockwise to reduce it.

• Press the tension lever down again to engage the

setting.

If the tension is correct, the saw blade should produce

a light tone when it is plucked, like a string.

8.3 Calibrating the angle scale (g. 12, 12.1)

IMPORTANT

Check the adjustment of the angular scale before you

start working with the unit.

1. Loosen the locknut of the adjustment screw (37).

2. To set the saw table, use a 90° bracket (31, not in

the scope of delivery). Place this against the saw

table and the saw blade (g. 12).

3. Adjust the adjustment screw (37) until the angle

between the saw blade (22) and the saw table (6)

is 90°.

4. Tighten the locknut of the adjustment screw (37)

again.

5. Loosen the screw (32) and turn the pointer (33) to

the 0° marking.

6. Make a test cut. Check the angle on the workpiece

with a protractor. If necessary, readjust the pointer

(33).

8.4 Installing the blow-o󰀨 device (g. 8)

1. Ensure that the saw blade guard (5) folded down.

2. Screw the blow-o󰀨 device (1) clockwise onto the

holder (2) as described in g. 8.

4. Then loosen the upper saw blade clamping lever

(28), followed by the lower saw blade clamping le-

ver (29) using the Allen key (23).

8.1.2 Inserting the saw blade without pins

(optional)

The teeth of the saw blade must always point down-

wards.

1. First, secure the saw blade (22) in the lower saw

blade mounting (30). To secure the saw blade (22),

tighten the lower saw blade clamping screw (29)

using the Allen key (23).

2. Press the support (12) down lightly. Fasten the oth-

er end of the saw blade (22) in the top saw blade

holder (27) (see g. 9).

3. Fix the saw blade (22) with the upper blade clamp-

ing screw (28) (see g. 10).

4. Tighten the saw blade (22) with the clamping lever

(11), by pressing it down again. Check the tension

of the saw blade (22). If the tension is insu󰀩cient,

it can be increased by turning the lever clockwise.

First release the clamping lever (11).

5. Put the table insert (26) back.

8.1.3 Removing the saw blade with pins

1. To remove the saw blade (22), lift the table insert

(26) upwards.

2. First, release the tension by ipping the tension

lever (11) upwards. Continue reducing the tension

by turning clockwise as required.

3. Press the support (12) down lightly (see g. 9).

4. Pull the saw blade from the upper and lower saw

blade mounting (27/30).

8.1.4 Inserting the saw blade with pins

The teeth of the saw blade must always point down-

wards.

1. Insert one end of the saw blade (22) through the

drilled hole in the table. Insert the pins of the saw

blade (22) into the corresponding recesses of the

top and bottom saw blade holder (27/30).

2. First insert the saw blade (22), in the lower blade

holder (30).

3. Press the support (12) down lightly (see g. 9).

4. Check the position of the saw blade pins in the saw

blade mountings (27/30).

5. Tighten the saw blade (22) with the clamping lever

(11), by pressing it down again. Check the tension

of the saw blade (22). If the tension is insu󰀩cient,

it can be increased by turning the lever (11) clock-

wise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DECO-XLS Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info