Bedienungsanleitung Scheppach DECO-XLS (Seite 30 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

781462

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

www.scheppach.com

30 | GB

7.3 Installing the fretsaw on a workbench

Required for installing:

Included in the scope of delivery:

• M8 hexagonal bolt (4x)

• M8 hexagonal nut (4x)

• Washer Ø 9 mm (8x)

The length of the screws to be used varies, depending

on the thickness of the table top.

WARNING

Danger of injury! Disconnect the mains plug on the

scroll saw before all assembly work.

1. The length of the screws to be used varies, de-

pending on the thickness of the table top.

2. Mark the drill holes (see g. 5.2).

3. Drill 4 holes with a diameter of 8 mm into the work

table.

4. Screw the scroll saw onto the workbench with the

hexagonal bolt (E) through the assembly points

(g. 3 pos. 19) in the following sequence (g. 5.1):

A Fretsaw

B Work table

C Washer

D Hexagonal nut

5. Tighten the hexagonal nut (D) rst.

8. Assembly

WARNING

Danger of injury! Disconnect the mains plug on the

scroll saw before all assembly work.

8.1 Fitting / Replacing the saw blade (g. 1, 8-11)

IMPORTANT

To avoid injuries attributed to inadvertent startup: Be-

fore removing or replacing the saw blade, always press

“0“ and remove the mains plug from the socket.

8.1.1 Removing the saw blade without pins (option-

al)

1. To remove the saw blade (22) , lift the table insert

(26) upwards.

2. First, release the tension by ipping the tension

lever (11) upwards. Continue reducing the tension

by turning clockwise as required.

3. Press the support (12) down lightly (see g. 9).

• Adopt your way of working to the equipment.

• Do not overload the equipment.

• Have the equipment checked if necessary.

• Switch o󰀨 the equipment when not in use.

Suitable saw blades

All industry-standard saw blades with a minimum

length of 127 mm with and without a pin may be used.

7. Before starting the machine

7.1 Unpacking

• Open the packaging and remove the device care-

fully.

• Remove the packaging material as well as the pack-

aging and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport

damage.

• If possible, store the packaging until the warranty

period has expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, lm and small parts! There is a risk of swal-

lowing and su󰀨ocation!

7.2 General notes

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you actuate the On/O󰀨 switch, make sure

that the saw blade is correctly tted and that the

equipment’s moving parts run smoothly.

• Check that the voltage on the rating plate is the

same as your supply voltage before you connect the

equipment to the power supply.

• Only ever connect the equipment to a properly in-

stalled shock-proof socket which is protected by a

10A fuse as a minimum.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DECO-XLS Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info