Bedienungsanleitung Scheppach GS55 (Seite 22 von 60) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

781395

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

• Then remove the aluminium cover (18) by releas-

ing the eight Phillips screws (Fig. I).

Clean the countersunk screw (Fig. K)

• With either a small screwdriver or a nail, remove

debris from the inner hexagon socket of the coun-

tersunk screw (20).

Blade (19) removal

• The T-handle pin-key has to completely reach into

the inner hexagon socket in order to unscrew the

screw.

• The blade, as well as the blade surface area of the

cutting disc, must be cleaned of hardened debris

material.

Sharpening the blade

• In resharpening the blade (19), pay close attention

to maintaining an even blade-diameter so as to

avoid an imbalanced blade.

• In resharpening the blade, a maximum of only 2

mm may be removed from each cutting edge.

Install Blade

• Upon reinstallation, the blade disc (19) must be

mounted exactly as before.

• In mounting the blade, lubricate the at head

screws (20) and tighten well.

• Tighten the countersunk screw rmly.

• Mount the aluminium cover.

• Use the locking screw to close the housing

• The device is ready for operation.

Overload protection

In the event of overload, e.g. due to branches that are

too thick, the equipment automatically switches off.

After a short cooling period (approximately 5 min-

utes), press the reset switch (7).

10. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

Assembling the stand to the machine body

(Fig. F, G)

• Fit the supporting feets (6) onto the threaded bolts

(17) of the machine body (2) (Fig. F)

• Fit the supplied lock nuts (14) by hand and tighten

them with the wrench (a) (Fig. G).

Attaching the Collecting bag (Fig. M, N)

To collect the chopped material, attach the supplied

collecting bag (21) to the hooks (3) provided (Fig. N).

9. Operation

Control panel (Fig. L)

• On switch (9): Tilt the button upwards; the shred-

der starts.

• Off switch (9): Tilt the button downwards; the

shredder stops.

• Reset-switch (7): Overload protection

Working with the shredder

Alternating with branches, shred withered gar-

den waste and branches that have been stored

several days to prevent the shredder from be-

coming blocked.

• Connect the shredder to the power supply.

• Turn the shredder on by using the on switch (9).

• Fill shredding material into the feed hopper and it

will be drawn in.

• Make sure the shredder has completely shred-

ded the input material before adding new.

• Do not use your hands to push in more shredding

material. Use the special pushing device (c) or oth-

er shredding material.

• When you have nished working with the shredder,

turn it off and disconnect it from the mains.

Changing the knife

Await complete standstill of cutter. Before work-

ing on cutter, remove mains plug.

The reversible steel blade can be used on both sides

and can be replaced quickly and easily.

Caution when working: There is a danger to ngers

and hands. It is extremly important to use only well

sharpened knives.

So please note:

A blunt knife impairs cutting performance and makes

work difcult.

A sure sign of a blunt knife is a reduction in automatic

pull. Engine heats up, overload protection triggers.

Open the housing (Fig. H, I)

• First open the housing by releasing the locking

screw (9). Then fold the upper section (2) of the

housing outward (Fig. H)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach GS55 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info