Bedienungsanleitung Scheppach HL810 (Seite 21 von 92) (Deutsch, Englisch, Französisch, Italienisch)

781857

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 21

Stroke limit for short logs, Fig. 10

Lower splitting knife position about 10 cm above ta-

ble.

• Move splitting knife to the desired position

• Release one operating arm

• Switch motor off

• Release the second operating arm

• Undo the star grip screw (10a)

• Push the stroke set rod (8) to the top until it is

stopped by the spring

• Tighten the star grip screw (10a) again.

• Switch motor on

• Check upper position

Switching on and off (12)

Press the green button for switching on.

Press the red button for switching off.

Note: Check the function of the ON/OFF unit before

every use by switching on and off once.

Restarting safety in case of current interruption

(no-volt release).

In case of current failure, inadvertent pulling of the

plug, or a defective fuse, the machine is switched off

automatically.

For switching on again, press anew the green button

of the switch unit.

Splitting

• Place the log on the table, hold it with both handles,

press the handles down. As soon as the splitting

knife enters the wood, push the handles down and

to the outside at the same time. This prevents the

wood from putting pressure on the holder plates.

• Only split straight cut logs.

• Split the logs in vertical position.

• Never split in horizontal position or across.

• Wear protective gloves when splitting.

End of work

• Move the splitting knife to the lower position.

• Release one operating arm.

• Switch the machine off and pull the power plug.

• Close the venting cap.

• Observe the general maintenance instructions.

Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the ap-

plicable VDE and DIN provisions.

The customer‘s mains connection as well as the ex-

tension cable used must also comply with these reg-

ulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

10. Initial operation

Make sure the machine is completely and expertly as-

sembled. Check before every use:

• The connection cables for any defective spots

(cracks, cuts etc.).

• The machine for any possible damage.

• 

• The hydraulic system for leakage.

• The oil level.

Checking the oil level (Fig. 13)

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage the

oil pump. The correct oil level is approx. 10 to 20 mm

below the oil tank surface.

Note: The level of oil must be checked when the riving

knife is pulled back. If the oil level is at the lower notch,

then the oil level is at a minimum. Should this be the

case, oil must be immediately added. The upper notch

indicates the maximum oil level. The machine must

be on level ground. Screw in the oil dipstick fully, to

measure the oil level.

Functional test

Test the function before every use.

Action: Result:

Push both handles towards

below.

Splitting knife goes

down to approx. 10

cm above the table.

Let one handle loose, then

the other.

Splitting knife stops

in the desired po-

sition.

Let both handles loose. Splitting knife

returns to upper

position.

Check the oil level before every use – see chapter

“Maintenance“.

Venting, Fig. 14

Before working with the log splitter, vent the hydraulic

system.

• Release the venting cap 6 by a few revolutions so

the air can escape from the oil tank.

• Leave the cap open during the operation.

• Before you move the log splitter, close the cap

again in order not to lose any oil.

If the hydraulic system is not vented, the enclosed air

will damage the gaskets and with it the complete log

splitter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL810 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info