Bedienungsanleitung Scheppach HL810 (Seite 22 von 92) (Deutsch, Englisch, Französisch, Italienisch)

781857

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

13. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and



Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

14. Maintenance

Attention!

Pull out the power plug before carrying out any main-

tenance work on the equipment.

When must the oil be changed?

First oil change after 50 operating hours, then every

500 operating hours.

Oil change (Fig. 12)

• Completely retract the splitting column.

• Put a container with a volume of at least 6 litres

under the splitter.

• Release the oil dipstick 6.

• Open the oil drain plug 12a under the oil tank so the



• Afterwards, close the oil drain plug 12a again.

• Remove the ventilation cap, pour in 4 litres of fresh

hydraulic oil using a clean funnel.

• Screw the oil dipstick in again.

Dispose of the used oil in a correct manner at a

public collection facility. It is prohibited to drop

old oil on the ground or to mix it with waste.

We recommend oil from the HLP 32 range.

Splitting spar

Before use, the spar of the splitter must be slightly



hours. Slightly apply grease of oil spray. The spar

may never run dry.

Hydraulic system

The hydraulic unit is a closed system with oil tank, oil

pump and control valve.

The system is complete when the machine is deliv-

ered, and may not be changed or manipulated.

Connections and repairs

Connections and repairs of electrical equipment may

only be carried out by an electrician.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insula-

tion damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H07RN“.

The printing of the type designation on the connec-

tion cable is mandatory.

For single-phase AC motors, we recommend a fuse

rating of 16A (C) or 16A (K) for machines with a high

starting current (starting from 3000 watts)!

AC motor 230 V/ 50 Hz

Mains voltage 230 Volt / 50 Hz.

The mains connection and the extension cable have

to be three-core cables = P + N + SL. - (1/N/PE).

Extension cables must have a minimum cross-section

of 1.5 mm². Mains fuse protection is 16 A maximum.

11. Cleaning

Attention!

Pull out the power plug before carrying out any clean-

ing work on the equipment.

We recommend that you clean the equipment imme-

diately after you use it.

Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these may be aggressive to the plastic parts in

the equipment. Ensure that no water can get into the

interior of the equipment.

12. Transport

For transport, the splitting knife A must be completely

moved down. Slightly tilt the log splitter with handle B

on the splitting column until the machine is inclined on

the wheels and can be moved. (Fig 11)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL810 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info