Bedienungsanleitung Scheppach HM216 (Seite 30 von 168) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

781430

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

30 | GB

• Loosen the lock nut (27a) and adjust the adjustment

screw (27) until the angle between the saw blade

(6) and the rotary table (14) is precisely 45°.

• Re-tighten the lock nut (27a).

• Subsequently check the position of the angle indi-

cator. If necessary, loosen the pointer (19) using a

Philips screwdriver, set to position 45° on the angle

scale (18) and re-tighten the retaining screw.

8.6 Mitre cut 0°- 45° and turntable 0° (g. 1/2/11)

The crosscut, drag and mitre saw can be used to

make mitre cuts of 0° - 45° in relation to the work face.

Attention! For mitre cuts (inclined saw head), the left

side

the outer position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) out-

wards.

•         

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a minimum of 8 mm.

• The right side of the moveable stop rails (16a)

must be in the inner positiion.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Move the machine head (4) to the top position.

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1)

to angle the machine head (4) to the left, until the

pointer (19) indicates the desired angle measure-

ment on the scale (18).

• Re-tighten the set screw (22).

• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(g. 2/4/12)

The crosscut, drag and mitre saw can be used to

make mitre cuts to the left of 0°- 45° in relation to the

work face and, at the same time, 0° - 45° to the left or

0° - 45° to the right in relation to the stop rail (double

mitre cut).

Attention! For mitre cuts (inclined saw head), the left

side

the outer position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) out-

wards.

•         

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a minimum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

Attention! The machine executes an upward stroke

automatically due to the return spring, i.e. do not

release the handle (1) after completing the cut; in-

stead allow the machine head to move upwards

slowly whilst applying light counter pressure.

8.4 Crosscut 90° and turntable 0° - 45° (g. 1/7/8)

The crosscut, drag and mitre saw can be used to

make crosscuts of 0° -45° to the left and 0° -45° to the

right in relation to the stop rail.

Important! For 90° crosscuts, the moveable stop rail



• Open the set screw (16b) for the moveable stop

rail (16a) and push the moveable stop rail (16a) in-

wards.

•         

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a minimum of 8 mm.

• Before making the cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Loosen the handle (11) if tightened, pull up the

       

and use the handle (11) to set the rotary table (14)

to the desired angle.

• The pointer (12) on the rotary table must match the

         

table (15).

• Re-tighten the handle (11) to secure the rotary table

(14).

• Cut as described under section 8.3.

8.5 Precision adjustment of the stop for mitre cut

45° (g. 1/2/5/9/10)

• No stop angle included.

• Lower the machine head (4) and secure it using the

locking bolt (23).

• Fix the rotary table (14) in the 0° position.

Attention! For mitre cuts (inclined saw head), the left

side

the outer position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) out-

wards.

•         

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• The right side of the moveable stop rails (16a)

must be in the inner positiion.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Loosen the set screw (22) and use the handle (1) to

angle the machine head (4) 45° to the left.

• 45° - position angle stop (B) between the saw blade

(6) and rotary table (14).

Scheppach HM216 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info