Bedienungsanleitung Scheppach HM216 (Seite 31 von 168) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

781430

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 31

•         

screw (29) in the clockwise direction.

• 



• 󰀨

out downwards.

• 



• Fit and fasten the new saw blade (6) in reverse or-

der.

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (6)

must coincide with the direction of the arrow on the

housing.

• Before continuing your work make sure that all safe-

ty devices are in good working condition.

• Important! Every time that you change the saw

blade (6), check to see that it spins freely in the ta-

ble insert (10) in both perpendicular and 45° angle

settings.

• Important! The work to change and align the saw

blade (6) must be carried out correctly.

8.11 Using the laser (g. 18)

Press the ON/OFF switch laser (33) 1x. A laser line is

projected onto the material you wish to process, pro-

viding an exact guide for the cut. Press again the ON/

OFF switch (34) to toggle between the laser (32) and

the LED working light (33):

ON/OFF switch laser/LED (34)

Press 1x. Laser ON / LED OFF

Press 2x. Laser OFF / LED ON

Press 3x. Laser ON / LED ON

Press 4x. Laser OFF / LED OFF

8.12 Adjusting the laser (g. 19-20)

If the laser (32) ceases to indicate the correct cutting

line, you can readjust the laser. To do so, open the

screws (32b) and remove the front cover (32a). Loos-

en the Philips head screws (E) and set the laser by

moving sideways until the laser beam strikes the teeth

of the saw blade (6).

After adjusting and tightening the laser, mount the

front cover by tightening both screws (32b) by hand.

9. Transport

• Tighten the handle (11) to lock the rotary table.

• Press the machine head (4) downwards and secure

with the locking bolt (23).

• Fix the saw’s drag function with the locking screw

for drag guide (20) in rear position.

• 

• When reassembling the equipment proceed as de-

scribed under section 7.

• Release the rotary table (14) by loosening the han-

dle (11).

• Using the handle (11), set the rotary table (14) to the

desired angle (refer also to point 8.4 in this regard).

• Re-tighten the handle (11) to secure the rotary table

(14).

• Undo the set screw (22).

• Use the handle (1) to tilt the machine head (4) to the

left until it coincides with the required angle value (in

this connection see also section 8.6).

• Re-tighten the set screw (22).

• Cut as described under section 8.3.

8.8 Limiting the cutting depth (g. 3/13)

•        

the screw (24). To do this loosen the knurled nut

(24a) on the screw (24). Turn the screw (24) in or

out to set the required cutting depth. Then re-tighten

the knurled nut (24a) on the screw (24).

• Check the setting by completing a test cut.

8.9 Sawdust bag (g. 1/22)

The saw is equipped with a debris bag (17) for sawdust

and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a

zipper at the bottom.

Connection to an external dust extractor

• Connect the vacuum hose with the dust extraction

spout.

• The industrial vacuum cleaner must be suitable for

the material being worked.

• When vacuuming dust that is especially detrimen-

tal to health or carcinogenic, use a special vacuum

cleaner.

8.10 Changing the saw blade (g. 1/2/14-17)

Remove the power plug!

Important!

Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing the machine head (4) upwards and lock with

the locking bolt (23).

• Loosen the retaining screw (5a) of the cover using a

Philips screwdriver.

WARNING! Do not fully remove this screw.

• Fold the saw blade guard (5) upwards until the saw



• 

screw (29).

• Hold the Allen key (C) and slowly close the saw

blade guard (5) until it touches the Allen key (C).

• Firmly press the saw shaft lock (30) and slowly ro-

       

The saw shaft lock (30) engages after no more than

one rotation.

Scheppach HM216 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info