Bedienungsanleitung Scheppach HM216 (Seite 32 von 168) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

781430

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

32 | GB

11. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The



Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

• The product meets the requirements of EN 61000-

3-11 and is subject to special connection conditions.

This means that use of the product at any freely se-

lectable connection point is not allowed.

• Given unfavourable conditions in the power supply

-

porarily.

• The product is intended solely for use at connection

points that

a) do not exceed a maximum permitted supply im-



b) have a continuous current-carrying capacity of

the mains of at least 100 A per phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets one of the two requirements,

a) or b), named above.

Important information

In the event of an overloading the motor will switch

 󰀨      

motor can be switched back on again.

Damaged electrical connection cable.

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

󰀨-

ing a cloth. In order to extend the service life of the tool, oil

the rotary parts once monthly. Do not oil the motor.

When cleaning the plastic do not use corrosive products.

Cleaning the moving saw blade guard safety de-

vice (5)

Always check the saw blade guard for debris before

using the machine.

Remove old sawdust and splinters using a brush or

similar tool.

Replacing the table insert

Danger!

• With a damaged table insert (10) there is a risk of

small parts getting stuck between table insert and

saw blade, blocking the saw blade. Immediately

replace damaged table inserts!

1. Remove screws at table insert. If required, turn ro-

tary table and incline saw head to be able to reach

the screws.

2. Remove table insert.

3. Install new table insert.

4. Tighten the screws at table insert.

Brush inspection



hours with a new machine, or when new brushes have



the check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the

spring or contact wire are burned or damaged, it is

necessary to replace both brushes. If the brushes are

found to be usable following removal, it is possible to

reinstall them.

When servicing the carbon brushes, open the two

latches counterclockwise (as shown in Figure 21).

Then remove the carbon brushes.

Replace the carbon brushes in the reverse order.

Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the follow-

ing parts are therefore also required for use as con-

sumables.

Wear parts*: carbon brushes, saw blade, table inserts,

sawdust bags

* Not necessarily included in the scope of delivery!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM216 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info