Bedienungsanleitung Scheppach HM90MP (Seite 29 von 168) (Deutsch, Englisch, Französisch, Italienisch, Polnisch, Alle Sprachen)

781435

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

• Workpiece supports (8) must always be secured

and used during work. Set the desired table size

by loosening the set screw (9). Then tighten the set

screw (9) again.

8.2 Precision adjustment of the stop for crosscut

90° (g. 1, 2, 5, 6)

No stop angle included.

• Lower the machine head (4) and secure it using the

locking bolt (23).

• Loosen the set screw (22).

• Position the angle stop (A) between the saw blade

(6) and the rotary table (14).

• Loosen the lock nut (26a).

• Adjust the adjusting screw (26) until the angle be-

tween the saw blade (6) and rotary table (14) is 90°.

• Re-tighten the lock nut (26a).

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (19) using a

Philips screwdriver, set to position 0° on the angle

scale (18) and re-tighten the retaining screw.

8.3 Crosscut 90° and turntable 0° (g. 1, 2, 7)

In the case of cutting widths up to approx. 100 mm it

is possible to x the traction function of the saw with

the set screw (20) in the rear position. In this position

the machine can be operated in cross cutting mode. If

the cutting width is over 100 mm then it is necessary

to ensure that the set screw (20) is loose and the ma-

chine head (4) can move.

Attention!

For 90° crosscuts, the moveable stop rail (16a) must

be xed in the inner position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) inwards.

• The moveable stop rail (16a) must be locked in a

position far enough from the inner position that the

distance between the stop rail (16a) and the saw

blade (6) is no more than 8 mm.

• Before making the cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Use the handle (1) to push back the machine head

(4) and x it in this position if required (dependent on

the cutting width).

• Place the piece of wood to be cut at the stop rail (16)

and on the turntable (14).

• Lock the material with the clamping devices (7) on

the xed saw table (15) to prevent the material from

moving during the cutting operation.

• Release the lock switch (3) and press the ON/OFF

switch to start the motor.

• With the drag guide (21) xed in place:

use the handle (1) to move the machine head (4)

steadily and with light pressure downwards until the

saw blade (6) has completely cut through the work

piece

• Pull out the pre-installed tilt protection (35) com-

pletely and secure it with an Allen key.

• Adjust the adjusting screw (36) to the level of the

tabletop to avoid wobbling of the machine.

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power

supply make sure the data on the rating plate are

dentical to the mains data.

7.1 Checking the moving saw blade guard safe-

ty device (5)

The saw blade guard protects against accidental con-

tact with the saw blade and from chips ying around.

Check function

To do so, fold the saw downwards:

• The saw blade guard must provide free access to

the saw blade without touching other parts.

• When folding the saw upwards into the starting

position, the saw blade guard must cover the saw

blade automatically.

8. Attachment and operation

8.1 Assembling the trim, chop and mitre saw

(g. 1, 2, 4, 5, 21)

• In order to adjust the rotary table (14), fold the lock-

ing handle (11) upwards and pull up the latched po-

sition lever (34) with your index nger.

• Turn the rotary table (14) and pointer (12) to the de-

sired angle measurement of the scale (13). To x

the setting, fold the locking handle (11) downwards.

• Pressing the machine head (4) lightly downwards

and removing the locking bolt (23) from the motor

bracket at the same time disengages the saw from

the lowest position.

• Swing the machine head (4) up.

• It is possible to secure the clamping devices (7) to

the left or right on the xed saw table (15). Insert

the clamping devices (7) in the holes on the rear

side of the stop rail (16) and secure it with the star

grip screws (7a).

• You can press the quick locking button (7b) to ad-

just the clamping device’s pressure plate (7) easily

to the workpiece height.

• For 0°- 45° mitre cuts, the clamping device (7) must

only be mounted on the right side (see g. 11-12).

• It is possible to tilt the machine head (4) a max. 45°

to the left by loosening the set screw (22).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM90MP Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info