Bedienungsanleitung Scheppach HM90MP (Seite 31 von 168) (Deutsch, Englisch, Französisch, Italienisch, Polnisch, Alle Sprachen)

781435

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 31

m Only use saw blades that comply with the ma-

chine specications regarding the bore diameter

and the maximum kerf of the saw blade.

m Only use saw blades which marked with a

speed equal or higher than the machine speci-

cations.

Wear safety gloves when changing the saw

blade. Risk of injury!

• Swing the machine head (4) upwards and lock with

the locking bolt (23).

• Fold the saw blade guard (5) upwards.

• Use one hand to insert the Allen key (C) in the

ange screw (28).

• Firmly press the saw shaft lock (30) and slowly ro-

tate the ange screw (28) in clockwise direction.

The saw shaft lock (30) engages after no more than

one rotation.

• Now, using a little more force, slacken the ange

screw (28) in the clockwise direction.

• Turn the ange screw (28) right out and remove the

outer ange (29).

• Take the blade (6) o󰀨 the inner ange (31) and pull

out downwards.

• Carefully clean the ange screw (28), outer ange

(29) and inner ange (32).

• Fit and fasten the new saw blade (6) in reverse or-

der.

• Important!

The cutting angle of the teeth, in other words the

direction of rotation of the saw blade (6) must coin-

cide with the direction of the arrow on the housing.

• Before continuing your work make sure that all

safety devices are in good working condition.

• Important!

Every time that you change the saw blade (6),

check to see that it spins freely in the table insert

(10) in both perpendicular and 45° angle settings.

• Important!

The work to change and align the saw blade (6)

must be carried out correctly.

8.11 Using the laser (g. 17)

• To switch on:

Press the ON/OFF switch laser (33) 1x. A laser line

is projected onto the material you wish to process,

providing an exact guide for the cut.

• To switch o󰀨:

Press again the ON/OFF switch laser (33).

8.12 Adjusting the laser (g. 18)

If the laser (32) ceases to indicate the correct cut-

ting line, you can readjust the laser. To do this, open

the screws (32b) and remove the front cover (32a).

Loosen the Philips head screws (D) and set the laser

by moving sideways until the laser beam strikes the

teeth of the saw blade (6).

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) out-

wards.

• The moveable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a minimum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Fold the locking handle (11) upwards to loosen the

rotary table (14).

• Set the rotary table (14) to the desired angle (refer

also to point 8.4 in this regard).

• Fold the locking handle (11) downwards to secure

the rotary table (14).

• Undo the set screw (22).

• Use the handle (1) to tilt the machine head (4) to the

left until it coincides with the required angle value

(in this connection see also section 8.6).

• Re-tighten the set screw (22).

• Cut as described under section 8.3.

8.8 Limiting the cutting depth (g. 3, 13)

• The cutting depth can be innitely adjusted using

the screw (24). To do this loosen the knurled nut

(24a) on the screw (24). Turn the screw (24) in or

out to set the required cutting depth. Then re-tight-

en the knurled nut (24a) on the screw (24).

• Check the setting by completing a test cut.

8.9 Chip collection bag (g. 1, 20)

The saw is equipped with a debris bag (17) for saw-

dust and chips.

Attention!

The chip collection bag may only be used when cut-

ting wood and wood-like materials!

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a

zipper at the bottom.

Connection to an external dust extractor

• Connect the vacuum hose with the dust extraction

spout.

• The industrial vacuum cleaner must be suitable for

the material being worked.

• When vacuuming dust that is especially detrimen-

tal to health or carcinogenic, use a special vacuum

cleaner.

8.10 Changing the saw blade (g. 1, 2, 14-16)

Remove the power plug!

Important!

m Always use the correct saw blade for the ma-

terial to be sawn.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM90MP Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info