Bedienungsanleitung Scheppach HM90MP (Seite 30 von 168) (Deutsch, Englisch, Französisch, Italienisch, Polnisch, Alle Sprachen)

781435

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

30 | GB

• The moveable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• The right side of the moveable stop rails (16a)

must be in the inner position.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Loosen the set screw (22) and use the handle (1) to

angle the machine head (4) 45° to the left.

• 45° - position angle stop (B) between the saw blade

(6) and rotary table (14).

• Loosen the lock nut (27a) and adjust the adjustment

screw (27) until the angle between the saw blade

(6) and the rotary table (14) is precisely 45°.

• Re-tighten the lock nut (27a).

• Subsequently check the position of the angle indi-

cator. If necessary, loosen the pointer (19) using a

Philips screwdriver, set to position 45° on the angle

scale (18) and re-tighten the retaining screw.

8.6 Mitre cut 0°- 45° and turntable 0° (g. 1, 2, 11)

The trim, chop and mitre saw can be used for mitre

cuts of 0°- 45° to the left of the work surface.

Attention!

For mitre cuts (inclined saw head), the left side of the

moveable stop rails (16a) must be xed in the outer

position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a minimum of 8 mm.

• The right side of the moveable stop rails (16a)

must be in the inner position.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Move the machine head (4) to the top position.

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1)

to angle the machine head (4) to the left, until the

pointer (19) indicates the desired angle measure-

ment on the scale (18).

• Re-tighten the set screw (22).

• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(g. 2, 4, 12)

The trim, chop and mitre saw can be used for mitre

cuts of 0°- 45° to the left of the work surface and of

0°- 45° to the stop rail (double mitre cut).

Attention!

For mitre cuts (inclined saw head), the left side of the

moveable stop rails (16a) must be xed in the outer

position.

• With the drag guide (21) not xed in place:

pull the machine head (4) all the way to the front.

Lower the handle (1) to the very bottom by applying

steady and light downward pressure. Now push the

machine head (4) slowly and steadily to the very

back until the saw blade (6) has completely cut

through the work piece.

• When the cutting operation is completed, move the

machine head back to its upper (home) position

and release the ON/OFF button (2).

Attention!

The machine executes an upward stroke automati-

cally due to the return spring, i.e. do not release the

handle (1) after completing the cut; instead allow

the machine head to move upwards slowly whilst

applying light counter pressure.

8.4 Crosscut 90° and turntable 0° - 45°

(g. 1, 7, 8)

The trim, chop and mitre saw can be used for angled

cuts of 0°-45° to the left and right.

Important!

For 90° crosscuts, the moveable stop rail (16a) must

be xed in the inner position.

• Open the set screw (16b) for the moveable stop

rail (16a) and push the moveable stop rail (16a) in-

wards.

• The moveable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a minimum of 8 mm.

• Before making the cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Loosen the locking handle (11) if tightened, pull up

the latched position lever (34) with your index nger

and use the locking handle (11) to set the rotary

table (14) to the desired angle.

• The pointer (12) on the rotary table must match the

desired angle on the scale (13) on the xed saw

table (15).

• Re-tighten the locking handle (11) to secure the ro-

tary table (14).

• Cut as described under section 8.3.

8.5 Precision adjustment of the stop for mitre cut

45° (g. 1, 2, 5, 9, 10)

No stop angle included.

• Lower the machine head (4) and secure it using the

locking bolt (23).

• Fix the rotary table (14) in the 0° position.

Attention!

For mitre cuts (inclined saw head), the left side of

the moveable stop rails (16a) must be xed in the

outer position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) out-

wards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM90MP Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info