Bedienungsanleitung Scheppach HS116 (Seite 34 von 72) (Deutsch, Englisch, Französisch)

782563

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

34 | GB

a) Never stand directly in line with the saw blade.

Always position your body on the same side of

the saw blade as the fence. Kickback may pro-

pel the workpiece at high velocity towards anyone

standing in front and in line with the saw blade.

b) Never reach over or in back of the saw blade

to pull or to support the workpiece. Accidental

contact with the saw blade may occur or kickback

may drag your ngers into the saw blade.

c) Never hold and press the workpiece that is be-

ing cut o󰀨 against the rotating saw blade. Press-

ing the workpiece being cut o󰀨 against the saw

blade will create a binding condition and kickback.

d) Align the fence to be parallel with the saw

blade. A misaligned fence will pinch the work-

piece against the saw blade and create kickback.

e) Use a featherboard to guide the workpiece

against the table and fence when making non-

through cuts such as rabbeting, dadoing or re-

sawing cuts. A featherboard helps to control the

workpiece in the event of a kickback.

f) Use extra caution when making a cut into blind

areas of assembled workpieces. The protruding

saw blade may cut objects that can cause kickback.

g) Support large panels to minimise the risk of

saw blade pinching and kickback. Large pan-

els tend to sag under their own weight. Support(s)

must be placed under all portions of the panel

overhanging the table top.

h) Use extra caution when cutting a workpiece

that is twisted, knotted, warped or does not

have a straight edge to guide it with a mitre

gauge or along the fence. A warped, knotted,

or twisted workpiece is unstable and causes mis-

alignment of the kerf with the saw blade, binding

and kickback.

i) Never cut more than one workpiece, stacked

vertically or horizontally. The saw blade could

pick up one or more pieces and cause kickback.

j) When restarting the saw with the saw blade

in the workpiece, centre the saw blade in the

kerf so that the saw teeth are not engaged in

the material. If the saw blade binds, it may lift up

the workpiece and cause kickback when the saw

is restarted.

k) Keep saw blades clean, sharp, and with suf-

cient set. Never use warped saw blades or

saw blades with cracked or broken teeth.

Sharp and properly set saw blades minimise bind-

ing, stalling and kickback.

g) Do not perform any operation “freehand”.

Always use either the rip fence or the mitre

gauge to position and guide the workpiece.

“Freehand” means using your hands to sup-

port or guide the workpiece, in lieu of a rip

fence or mitre gauge. Freehand sawing leads to

misalignment, binding and kickback.

h) Never reach around or over a rotating saw

blade. Reaching for a workpiece may lead to ac-

cidental contact with the moving saw blade.

i) Provide auxiliary workpiece support to the

rear and/or sides of the saw table for long and/

or wide workpieces to keep them level. A long

and/or wide workpiece has a tendency to pivot on

the table’s edge, causing loss of control, saw blade

binding and kickback.

j) Feed workpiece at an even pace. Do not bend

or twist the workpiece. If jamming occurs, turn

the tool o󰀨 immediately, unplug the tool then

clear the jam. Jamming the saw blade by the

workpiece can cause kickback or stall the motor.

k) Do not remove pieces of cut-o󰀨 material while

the saw is running. The material may become

trapped between the fence or inside the saw blade

guard and the saw blade pulling your ngers into

the saw blade. Turn the saw o󰀨 and wait until the

saw blade stops before removing material.

l) Use an auxiliary fence in contact with the ta-

ble top when ripping workpieces less than 2

mm thick. A thin workpiece may wedge under the

rip fence and create a kickback.

Kickback causes and related warnings

Kickback is a sudden reaction of the workpiece due

to a pinched, jammed saw blade or misaligned line of

cut in the workpiece with respect to the saw blade or

when a part of the workpiece binds between the saw

blade and the rip fence or other xed object.

Most frequently during kickback, the workpiece is lift-

ed from the table by the rear portion of the saw blade

and is propelled towards the operator.

Kickback is the result of saw misuse and/or incor-

rect operating procedures or conditions. And can be

avoided by taking proper precautions as given below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HS116 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info