Bedienungsanleitung Scheppach HS116 (Seite 35 von 72) (Deutsch, Englisch, Französisch)

782563

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 35

4. Do not use any insertion tools with cracks. Sort out

cracked insertion tools. Repairs are not permitted.

5. Clean dirt, grease, oil and water o󰀨 of the clamp-

ing surfaces.

6. Do not use any loose reducing rings or bushes to

reduce holes on circular saw blades.

7. Make sure that xed reducer rings for securing

the insertion tool have the same diameter and

have at least 1/3 of the cutting diameter.

8. Make sure that xed reducer rings are parallel to

each other.

9. Handle insertion tools with caution. They are ideally

stored in the originally package or special containers.

Wear protective gloves in order to improve grip and to

further reduce the risk of injury.

10. Prior to the use of insertion tools, make sure that

all protective devices are properly fastened.

11. Prior to use, make sure that the insertion tool

meets the technical requirements of this electric

tool and is properly fastened.

12. Only use the supplied saw blade for cutting wood,

never for the processing of metals.

13. Use the correct saw blade for the material to be

processed.

14. Use only a saw blade with a diameter that match-

es the specications on the saw.

15. Use only saw blades that are marked with an

equal or higher rotational speed than that marked

on the power tool.

16. Use only saw blades recommended by the manu-

facturer which conform to EN 847-1, if intended for

cutting wood or similar materials.

17. Wear suitable personal protective equipment,

such as:

– Hearing protection;

– Protective gloves when handling saw blades.

18. Only use saw blades recommended by the man-

ufacturer which conform to EN 847-1. Warning!

When changing the saw blade, ensure that the

cutting width is not smaller and the width of the

saw blade disc is not greater than the thickness

of the riving knife!

19. When sawing wood and plastics, avoid the saw

teeth overheating. Reduce the feed speed in or-

der to avoid the plastic melting.

20. Please note that complex non-through cutting op-

erations and tapered cuts are not permitted.

21. Avoid bevel ripping on bevelling side of the saw

blade.

22. Make sure when mounting or when installing the

parallel stop that it should be aligned parallel to

the saw blade.

Table saw operating procedure warnings

a) Turn o󰀨 the table saw and disconnect the power

cord when removing the table insert, changing

the saw blade or making adjustments to the riv-

ing knife or saw blade guard, and when the ma-

chine is left unattended. Precautionary measures

will avoid accidents.

b) Never leave the table saw running unattend-

ed. Turn it o󰀨 and don’t leave the tool until it

comes to a complete stop. An unattended run-

ning saw is an uncontrolled hazard.

c) Locate the table saw in a well-lit and level area

where you can maintain good footing and bal-

ance. It should be installed in an area that pro-

vides enough room to easily handle the size

of your workpiece. Cramped, dark areas, and

uneven slippery oors invite accidents.

d) Frequently clean and remove sawdust from

under the saw table and/or the dust collection

device. Accumulated sawdust is combustible and

may self-ignite.

e) The table saw must be secured. A table saw

that is not properly secured may move or tip over.

f) Remove tools, wood scraps, etc. from the ta-

ble before the table saw is turned on. Distrac-

tion or a potential jam can be dangerous.

g) Always use saw blades with correct size and

shape (diamond versus round) of arbour holes.

Saw blades that do not match the mounting hardware

of the saw will run o󰀨-centre, causing loss of control.

h) Never use damaged or incorrect saw

blade mounting means such as ang-

es, saw blade washers, bolts or nuts.

These mounting means were specially designed

for your saw, for safe operation and optimum per-

formance.

i) Never stand on the table saw, do not use it as

a stepping stool. Serious injury could occur if

the tool is tipped or if the cutting tool is acciden-

tally contacted.

j) Make sure that the saw blade is installed to ro-

tate in the proper direction. Do not use grind-

ing wheels, wire brushes, or abrasive wheels

on a table saw.

Improper saw blade installation or use of accesso-

ries not recommended may cause serious injury.

Safety instructions for the handling of saw

blades

1. Only use insertion tools if you have mastered their

use.

2. Observe the maximum speed. The maximum

speed specied on the insertion tool may not be

exceeded. If specied, observe the speed range.

3. Observe the motor / saw blade direction of rotation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HS116 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info