Bedienungsanleitung Scheppach HS116 (Seite 37 von 72) (Deutsch, Englisch, Französisch)

782563

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 37

9. Connect the machine stand part 2 (24b) with the

machine stand part 3 (24c) using two Phillips

screws M5 x 40 mm (D) and two nuts M5 (M) on

each side. (g. 12)

10. Fit two at end caps (N) on the ends of machine

stand part 3 (24c).

11. Connect the machine stand part 3 (24c) with the

machine stand part 6 (24f) using one coach bolt

M8 x 78 mm (A), one spacer (J) and one nut M8

(K) on each side. (g. 13)

NOTE: Do not over-tighten the screws. The parts

must be able to move freely.

12. Connect the machine stand part 4 (24d) with the

machine stand part 3 (24c) using one coach bolt

M8 x 78mm (A), one spacer (J) and one nut M8

(K) on each side. (g. 14)

13. Now connect both wheels (13) with the machine

stand part 4 (24d) using the wheel screws (P) as

shown in g. 15.

14. Turn the machine so that it rests on the machine

stand (24).

15. Release the locking latch (14) and fold up the ma-

chine stand until the locking pin engages into the

locking latch (14).

9.2 Removing the table inlay (g. 16)

1. Set the saw blade (1) to the max. cutting depth,

move to the 0° position and lock in place (see 11.2).

2. Loosen the xing screw (4a) by turning it a quarter

turn counterclockwise.

3. Remove the table inlay (4) from the saw table (5).

9.3 Riving knife

m WARNING

Danger of injury due to unexpected start-up of the

machine

- Remove the mains plug from the socket.

You need to remove the table inlay (4) before you can

install and adjust the riving knife (3).

9.3.1 Insertng and adjusting the riving knife (g.

17 + 18)

1. Loosen the xing screw (3a). (g. 17)

2. Push the riving knife (3) into the holder.

NOTE: This step is not necessary if the riving knife

(3) is already inserted.

3. Align the riving knife (3) such that

a) the distance between the saw blade (1) and the

riving knife (3) is max. 5 mm (g. 18) and

b) the saw blade (1) is parallel to the riving knife (3).

3. Tighten the xing screw (3a) again.

9.4 Fitting the table inlay (g. 16)

1. Place the table inlay (4) in the recess.

2. Tighten the xing screw (4a) by turning it a quarter

turn clockwise.

You require the following for assembly:

1x open-ended spanner 10/13 mm (26)

1x ring spanner 10/21 mm (27)

(included in the scope of delivery)

1x Phillips screwdriver

1x Allen key 5 mm

(not included in the scope of delivery)

• Place all supplied parts on a at surface.

• Group equal parts.

NOTE:

• If connections are secured with a screw (round-

head or hexagon), hexagon nuts and washers, the

washer must be tted under the nut.

• Insert screws each from outside to inside. Secure

connections with nuts on the inside.

• Tighten the nuts and screws during assembly only

until they are unable to fall o󰀨. If you tighten the

nuts and screws fully before nal assembly, it is not

possible to complete the assembly.

9.1 Fitting the machine stand (g. 5 - 15)

1. Turn the machine over and place it on a clean sur-

face. (g. 5)

2. Fasten the two machine stand parts (24f) on the

machine housing using two Allen screws M6 x 53

mm (B), two large washers (I) and two nuts M6 (L)

each. (g. 6)

3. Fit both round end caps (O) on the ends of the

machine stand parts (24f). (g. 6)

4. On the other side, t both at end caps (N) on the

ends of the machine stand parts (24f). (g. 6)

5. Connect the machine stand part 4 (24d) with the

machine stand part 5 (24e) using two Phillips screws

M5 x 50 mm (C) and two nuts M5 (M). (g. 7)

6. Connect the machine stand part 4 (24d) with the

machine stand part 1 (24a) using two coach bolts

M8 x 78 mm (A), two spacers (J) and two nuts M8

(K). (g. 8)

NOTE: Do not over-tighten the screws. The parts

must be able to move freely.

NOTE: Make sure that the locking latch (14) on ma-

chine stand part 4 (24d) is on the same side as the

locking pin on machine stand part 1 (24a). (g. 9)

7. Fit two at end caps (N) on the ends of machine

stand part 4 (24d). (g. 9)

8. Connect the machine stand part 4 (24d) with the

machine stand part 6 (24a) using two coach bolts

M8 x 78 mm (A), two spacers (J) and two nuts M8

(K). (g. 10 + 11)

NOTE: Do not over-tighten the screws. The parts

must be able to move freely.

NOTE: Make sure that the locking latch (14) is on

the same side as the on/o󰀨 switch (15).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HS116 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info