Bedienungsanleitung Scheppach HTH250 (Seite 24 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch)

782035

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

24 GB

- Support the hedge trimmer when starting and hold

it rmly. Make sure that the cutting device can move

freely.

To start the hedge trimmer:

1. Keep a safe distance to ammable materials.

2. Have a safe standing position.

3. Place the hedge trimmer on the ground in front of

you, with the cutting device showing away from

your body.

4. Put the right foot tip in the rear handle.

5. Hold the front handle with your left hand.

Starting with cold engine

1. Slide the ON/OFF switch (6) to the position „I„.

2. Carefully press on the fuel pump (11) several times

until fuel comes into the pump.

3. Slide the choke (4) to „cold start“.

4. Slowly pull the cranking rope with its handle (5) un-

til you feel a resistance.

5. Pull the cranking rope quickly and then guide it

back slowly. Do not fully pull out the cranking rope

and do not allow that the cranking handle strikes

against the engine.

6. When the engine starts slide the choke (4) to

„warm start and work“.

7. Allow the device to warm up for approx. 1 minute

before starting the work.

Stopping the engine

1. Release the throttle trigger (14).

2. Slide the ON/OFF switch (6) to the „0„ position.

Starting with warm engine

1. Slide the ON/OFF switch (6) to the position „I„.

2. Slide the choke lever (4) to „warm start and work“.

3. Hold the cranking handle (5) and pull the cranking

rope until the engine starts.

Throttle lock-out switch

1. Hold the hedge trimmer on its rear handle (15) and

press the throttle lock-out switch (7).

2. Hold the front handle (3) with your other hand.

3. Press the throttle trigger (14).

4. The cutting device will start moving.

• If you release the throttle trigger, the cutting device

will stop and the engine will idle.

If the cutting device runs in spite of non-pressed throttle

trigger, you have to reduce the idle speed. (See “Main-

tenance”.)

Adjustments on the hedge trimmer

Adjusting the rear handle (15).

To make working with the hedge trimmer easier it is

possible to choose one of the 3 working positions of the

rear handle.

• When adjusting the throttle trigger (14) can not be

pressed.

1. Use your left hand to hold the hedge trimmer on its

front handle (3).

2. Pull the slider (13) and turn the handle to your de-

sired position.

3. Release the slider (13). Make sure that the unlock-

ing device engages again and that the handle is

secured.

9. Working instructions

Carry out the following checks before starting and

regularly during working with the hedge trimmer:

• Is the hedge trimmer assembled completely and

properly? Check also that all nuts and screws are

tightened. Screws on the cutting device: See “Main-

tenance”.

• Is the hedge trimmer in good and safe condition? Do

all safety devices properly work?

• Is the fuel tank lled?

• Is the cutting device undamaged and sharpened?

• Are engine and silencer free from deposits, leaves or

emerging lubricants.

• Is handhold clean and dry – free of oil, grease and

resin?

• Is workplace free of risks to stumble?

• Do you wear the required protective equipment?

• Did you read and understand all advices?

• Is the throttle trigger easy-running and functioning?

• Does the ON/OFF switch properly work?

• Does the cutting device always stop in idle mode?

If the cutting device moves during idling the idle speed

must be reduced (see “Adjusting the idle speed”).

• Check that the gearbox is sufciently lubricated (see

“Maintenance”).

General behaviour when working with the hedge

trimmer

• Never work alone. Another person should stay close

enough to hear calls for help.

• Keep children, bystanders and animals at a distance

(15m min.) from your working area.

• Do not work on snow, ice or other slippery ground –

slip hazard.

• Do not work under insufcient light conditions (e.g.

fog, rain, snow urry or twilight).

• Scare animals off the hedge before starting to cut in

order to prevent them from being injured.

• Provide for a safe and cleaned workplace. Remove

from the working area objects which might be thrown

off.

• Avoid abnormal posture. Keep at any time the bal-

ance. Do not work with the upper part of the body

leaned forward.

• Operate the hedge trimmer only with safe standing

position.

• Stop the hedge trimmer when moving to another work

place.

• Keep hands and feet away from the cutting device

when it moves.

• Hold the hedge trimmer so that you do not inhale ex-

haust gases. Do not work in closed rooms.

• Do not use the hedge trimmer to pick up or remove

wood pieces or other objects.

• Remove unconditionally any foreign objects out of the

hedge (e.g. wires) as these can damage the knives of

the hedge trimmer.

• Hold the hedge trimmer always rmly with both

hands, left hand on the front handhold and right hand

on the rear handhold).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HTH250 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info