Bedienungsanleitung Scheppach HTH250 (Seite 25 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch)

782035

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

25GB

Pay attention to breeding birds in the hedge. If so, put

off hedge trimming or leave this area out.

At any case pay attention to all safety instructions.

10. Maintenance

Before each maintenance and cleaning work

- Stop the engine.

- Wait until the cutting device does not longer move.

- Stop the engine and pull off the spark plug connector

(with the exception of idle speed adjustment).

Do not carry out maintenance work close to open

ames. Risk of re.

Maintenance and repair work other than those de-

scribed in this chapter is only allowed to be carried out

by service staff.

For maintaining and cleaning, removed security

devices must unconditionally be mounted properly

and proved again.

Use only original parts. Other parts can result in unex-

pected damages and injuries.

In order to aviod possible injuries wear gloves.

To guarantee a long and reliable usage of the hedge

trimmer carry out the following maintainance works

regularly.

Check the hedge trimmer for obvious defects such

- loose fastening elements

- worn or damaged components

- deformed, broken or damaged cutting device

- leaks from the fuel tank cap or fuel lines

Check the hedge trimmer after each application for

- wear and tear, in particular sliding play of the cutting

device

- correct assembly and faultless covers and protective

devices.

Necessary repair or maintainance operations have to

be carried out before the usage of the hedge trimmer.

Adjusting the cutting device

Readjust the sliding play if cut material is clamped be-

tween the blades or the play has increased due to nor-

mal wearing of the cutting device after a longer period

of use.

To obtain good cutting results the free motion between

the blades and the sword must be correctly adjusted.

For this proceed as follows:

1. Loosen the nuts (A) on the top surface of the cut-

ting device.

2. Slightly tighten the screws (B) on the underside (if

required loosen them previously).

3. Turn the screw back anticlockwisely by a quarter

up to a half turn.

4. Use a screwdriver to hold the screw and rmly

tighten the nuts.

The sliding play is correctly adjusted if the washer under

the screw head can just be freely moved back and forth

by hand.

• If you release the throttle trigger the cutting device

will afterrun for a short time (free wheeling effect).

• Start trimming with the cutting device moving.

• Never touch the cutting device with your hands during

operation.

• Never work

- with stretched arms

- on hardly accessible places

- too far bent forward

• Never work with the hedge trimmer above shoulder

height.

• Never get in contact with the running cutting device

with metallic fences or the ground.

• Stop the engine and pull the spark plug connector:

- when you notice changes in the device’s behaviour,

- to remove jammed material,

- to check the cutting device after it had contact with

stones, nails or other hard objects,

- to eliminate faults,

- for work breaks,

- before leaving the hedge trimmer.

• Do not place a hot hedge trimmer in dry grass or onto

inammable objects.

• Before starting your work make sure that:

- no other persons or animals stay within the working

area,

- you can always step back without any barriers,

- your standing area is free from foreign objects,

brushwood and branches,

- you have always a secure standing position.

If persons who have blood circulation problems are too

often exposed to vibrations damages to the nervous

system or to blood vessels may occur.

You can reduce vibrations

- by thick and warm working gloves,

- shorter working time (have longer breaks).

See a doctor if your ngers swell, you don’t feel well or

your ngers become numb.

Working with the hedge trimmer

Hold the hedge trimmer with both hands on a safe

distance from the body.

• The maximal diameter to cut depends on the wood’s

type, age, moisture and hardness.

• Therefore cut very thick branches using branch shears

to your desired length before trimming the hedge.

• Due to its double sided knives the hedge trimmer can

be guided forward and backward or by oscillating

movements from one to another side.

• At rst cut the sides of the hedge and then the upper

edge.

• Cut the hedge from the bottom up.

• Cut the hedge in trapezium shape.

• Stretch a guide over the complete length of the hedge

when you want to shorten the upper edge of the

hedge evenly.

• Trim in several passes if you have to cut down a large

portion of the hedge.

Best time for hedge trimming:

• Leaved hedge: June and October

• Conifer hedge: April and August

• Quickly growing hedge: from May and then every 6

weeks

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HTH250 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info