Bedienungsanleitung Scheppach KZS-UG1800 Primaster (Seite 24 von 44) (Deutsch, Englisch, Französisch)

782504

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

24 GB

8 Do not weld or solder directly on batteries!

9 Do not dismantle batteries!

10 Do not allow batteries to deform!

11 Do not throw batteries into re!

12 Keep batteries out of the reach of children.

13 Do not allow children to replace batteries without

supervision!

14 Do not keep batteries near re, ovens or other

sources of heat. Do not use batteries in direct sun-

light or store them in vehicles in hot weather.

15 Keep unused batteries in the original packaging and

keep them away from metal objects. Do not mix

unpacked batteries or toss them together! This can

lead to a short-circuit of the battery and thus dam-

age, burns or even the risk of re.

16 Remove batteries from the equipment when it will

not be used for an extended period of time, unless

it is for emergencies!

17 NEVER handle batteries that have leaked without

appropriate protection. If the leaked uid comes into

contact with your skin, the skin in this area should be

rinsed off under running water immediately. Always

prevent the uid from coming into contact with the

eyes and mouth. In the event of contact, please seek

immediate medical attention.

18 Clean the battery contacts and corresponding con-

tacts in the device prior to inserting the batteries:

6. Technical data

AC motor 230 V ~ 50Hz

Power 1800 Watt

Operating mode S1

Idle speed n04800 min-1

Carbide saw blade ø 254 x ø 30 x 2,8 mm

Number of teeth 60

Swivel range -45° / 0°/ +60°

Mitre cut 0° bis 45° nach links

Saw width at 90° 305 x 75 mm

Saw width at 45° 210 x 75 mm

Saw width at 2 x 45°

(double mitre cut) 210 x 45 mm

Protection class II

Weight ca. 21 kg

Laser class 2

Wavelength of laser 650 nm

Laser output < 1 mW

Laser module power

supply 2 x 1,5 V Micro (AAA)

The work piece must have a minimum height of 3mm

and a minimum width of 10 mm.

Make sure that the workpiece is always secured with

the clamping device.

Noise

Total vibration values determined in accordance with

EN 61029.

sound pressure level LpA 86 dB(A)

uncertainty KpA 3 dB

sound power level LWA 99 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Residual risks

The machine has been built according to the state of

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instruc-

tions“ and the „Proper use“ are observed along with

the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the oper-

ating button may not be pressed when inserting the

plug in an outlet.

• Use the tool that is recommended in this manual. In do-

ing so, your mitre saw provides optimal performance.

• Hands may never enter the processing zone when

the machine is in operation. Release the handle but-

ton and switch off the machine prior to any operations.

7. Before starting the equipment

• The equipment must be set up where it can stand se-

curely, i.e. it should be bolted to a workbench, a uni-

versal base frame or similar.

• All covers and safety devices have to be properly t-

ted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails or

screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power sup-

ply make sure the data on the rating plate are dentical

to the mains data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KZS-UG1800 Primaster Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info