Bedienungsanleitung Scheppach KZS-UG1800 Primaster (Seite 26 von 44) (Deutsch, Englisch, Französisch)

782504

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

26 GB

• 45° - position angle stop (b) between the saw blade

(6) and rotary table (14).

• Adjust the adjusting screw (28) until the angle between

the saw blade (6) and rotary table (14) is precisely 45°.

• It is not necessary to x this setting because it is

maintained by the spring pretension.

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (19) using a

Philips screwdriver, set to position 45° on the angle

scale (18) and re-tighten the retaining screw.

8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/3/12)

The crosscut saw can be used to make mitre cuts of

0° - 45° in relation to the work face.

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (16a) must be xed at the outer

position.

• Open the set nut (16b) for the adjustable stop rail

(16a) and push the adjustable stop rail outwards.

• The adjustable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set nut (16b) again.

• Move the machine head (4) to the top position.

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1)

to angle the machine head (4) to the left, until the

pointer (19) indicates the desired angle measure-

ment on the scale (18).

• Re-tighten the xing screw (22).

• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(Fig. 2/3/4/13)

The crosscut saw can be used to make mitre cuts to

the left of 0°- 45° in relation to the work face and, at

the same time, 0° - 45° to the left or 0° - 45° to the

right in relation to the stop rail (double mitre cut).

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (16a) must be xed at the outer

position.

• Open the set nut (16b) for the adjustable stop rail

(16a) and push the adjustable stop rail outwards.

• The adjustable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set nut (16b) again.

• Move the machine head (4) to its upper position.

• Release the rotary table (14) by loosening the set

screw (26).

• Using the handle (11), set the rotary table (14) to the

desired angle (refer also to point 8.4 in this regard).

• Re-tighten the set screw (26) in order to secure the

rotary table.

• Undo the locking screw (22) and use the handle (1)

to tilt the machine head (4) to the left until it coin-

cides with the required angle value (in this connec-

tion see also section 8.6).

• Re-tighten the xing screw (22).

• Cut as described under section 8.3.

8.8 Limiting the cutting depth (Fig. 2/14)

• The cutting depth can be innitely adjusted using the

screw (24). To do this loosen the knurled nut on the

screw (24). Move the stop for the cutting depth limi-

tre (25) to the outside. Turn the screw (24) in or out

to set the required cutting depth. Then re-tighten the

knurled nut on the screw (24).

• Check the setting by completing a test cut.

8.9 Sawdust bag (Fig. 1)

The saw is equipped with a debris bag (17) for saw-

dust and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a zip-

per at the bottom.

8.10 Changing the saw blade (Fig. 15/16/17)

Remove the power plug!

Important.

Wear safety gloves when changing the saw blade.

Risk of injury!

• Unplug the machine.

• Position the sawing unit in the setting “clipping opera-

tion” (kappbetrieb).

• Unlock the movable saw blade protector (5) by means

of pressing on the lock (3).

• Lift up the saw blade protector so far that you can see

the saw blade mounting screw (29) in the notch in the

saw blade protector.

• Press down on the saw blade lock (31) until the saw

blade snaps into place.

• Remove the saw blade mounting screw (29) (note: left

hand groove).

• Remove bolt (29) and saw blade ﬂange (30).

• Take off the saw blade (6) with caution (risk of injury

through saw blade teeth).

• Place the new saw blade (6) onto the inner saw blade

ﬂange (32), observing the correct size and the turning

direction of the saw blade.

• Put the outer saw blade ﬂange (30) in place and ﬁrmly

tighten the screw (29).

• Return the saw blade guard (5) to the correct position.

8.11 Using the laser (Fig. 3/19/20)

• To switch on: Move the ON/OFF switch of the laser

(34) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact

guide for the cut.

• To switch off: Move the ON/OFF switch of the laser

(34) to the “0” position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KZS-UG1800 Primaster Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info