Bedienungsanleitung Scheppach KZS-UG1800 Primaster (Seite 25 von 44) (Deutsch, Englisch, Französisch)

782504

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

25GB

8. Attachment and operation

8.1 Attaching the saw (Fig1/2/3/4/5)

• In order to adjust the rotary table (14) loosen the set

screw (11) approx. 2 turns.

• Turn the rotary table (14) and pointer (12) to the de-

sired angle measurement on the scale (13) and secure

with the set screw (11).

• Pressing the machine head (4) lightly downwards and

removing the locking bolt (23) from the motor bracket

at the same time disengages the saw from the low-

est position.

• Swing the machine head (4) up until the release lever

(3) latches into place.

• It is possible to secure the clamping device (7) to the

left or right on the stationary saw bench (15).

• Attach the workpiece supports (8) to the xed saw

table (15) as shown in Figure 5 and fasten with the

screw (9).

• It is possible to tilt the machine head (4) a max. 45° to

the left by loosening the set screw (22).

8.2 Precision adjustment of the stop for crosscut

90° (Fig. 1/6/7)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Loosen the set screw (22).

• Position the angle stop (a) between the saw blade

(6) and the rotary table (14).

• Unscrew lock nut (27a)

• Adjust the adjusting screw (27) until the angle be-

tween the saw blade (6) and rotary table (14) is 90°.

• Tighten the lock nut (27a).

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (19) using a

Philips screwdriver, set to position 0° on the angle

scale (18) and re-tighten the retaining screw.

8.3 Cross cut 90° and turntable 0° (Fig. 3/8)

In the case of cutting widths up to approx. 100 mm it is

possible to x the traction function of the saw with the

set screw (20) in the rear position. In this position the

machine can be operated in cross cutting mode. If the

cutting width is over 100 mm then it is necessary to en-

sure that the set screw (20) is loose and the machine

head (4) can move.

Attention! For 90° cross cuts, the moveable stop rail

(16a) must be xed in the inner position.

• Open the set nut (16b) on the moveable stop rail

(16a) and push the moveable stop rail (28) inwards.

• The moveable stop rail (16a) must be locked in a po-

sition far enough from the inner position that the dis-

tance between the stop rail (16a) and the saw blade

(6) is no more than 8 mm.

• Before making the cut, check that no collision could oc-

cur between the stop rail (16a) and the saw blade (6).

• Tighten the set nut (16b) again.

• Move the machine head (4) to its upper position.

• Use the handle (3) to push back the machine head

(4) and x it in this position if required (dependent on

the cutting width).

• Place the piece of wood to be cut at the stop rail

(16) and on the turntable (14).

• Lock the material with the clamping device (7) on

the xed saw table (15) to prevent the material from

moving during the cutting operation.

• Push down the release lever (3) to release the ma-

chine head (4).

• Press the ON/OFF switch (2) to start the motor.

• With the drag guide (21) xed in place:

• use the handle (1) to move the machine head (4)

steadily and with light pressure downwards until the

saw blade (6) has completely cut through the work

piece.

• With the drag guide (21) not xed in place:

• pull the machine head (4) all the way to the front.

Lower the handle (1) to the very bottom by apply-

ing steady and light downward pressure. Now push

the machine head (4) slowly and steadily to the

very back until the saw blade (6) has completely cut

through the work piece.

• When the cutting operation is completed, move the

machine head (4) back to its upper (home) position

and release the ON/OFF button (2).

Attention! The machine executes an upward stroke

automatically due to the return spring, i.e. do not re-

lease the handle (1) after completing the cut; instead

allow the machine head to move upwards slowly

whilst applying light counter pressure.

8.4 Cross cut 90° and turntable 0° - 45° (Fig. 9)

The crosscut saw can be used to make crosscuts of 0°

-45° to the left and 0° -45° to the right in relation to the

stop rail.

Important. To make 90° crosscuts, the adjustable stop

rail (16a) must be xed at the inner position.

• Open the set nut (16b) for the adjustable stop rail

and push the adjustable stop rail inwards.

• The adjustable stop rail (29) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set nut (16b) again.

• Loosen set screw (26).

• Use the handle (11) to adjust the rotary table (14)

to the desired angle. The pointer (12) on the rotary

table must match the desired angle on the scale (13)

on the xed saw table (15).

• Re-tighten the set screw (11) in order to secure the

rotary table (14).

• Cut as described under section 8.3.

8.5 Precision adjustment of the stop for mitre cut

45° (Fig. 1/10/11)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1) to

angle the machine head (4) 45° to the left.

Scheppach KZS-UG1800 Primaster Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info