Bedienungsanleitung Scheppach KZS2000 Primaster (Seite 27 von 56) (Deutsch, Englisch, Französisch)

782511

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

GB | 27

5. Service

a) Have your power tool serviced by a qualied

repair person using only identical replace-

ment parts. This will ensure that the safety of the

power tool is maintained.

Safety instructions for mitre saws

a) Mitre saws are intended to cut wood or wood-

like products, they cannot be used with abra-

sive cut-o󰀨 wheels for cutting ferrous mate-

rial such as bars, rods, studs, etc. Abrasive

dust causes moving parts such as the lower guard

to jam. Sparks from abrasive cutting will burn the

lower guard, the kerf insert and other plastic parts.

b) Use clamps to support the workpiece when-

ever possible. If supporting the workpiece

by hand, you must always keep your hand

at least 100 mm from either side of the saw

blade. Do not use this saw to cut pieces that

are too small to be securely clamped or held

by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from

blade contact.

c) The workpiece must be stationary and

clamped or held against both the fence and

the table. Do not feed the workpiece into the

blade or cut “freehand” in any way. Unre-

strained or moving workpieces could be thrown at

high speeds, causing injury.

d) Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make

a cut, raise the saw head and pull it out over

the workpiece without cutting, start the mo-

tor, press the saw head down and push the

saw through the workpiece. Cutting on the pull

stroke is likely to cause the saw blade to climb on

top of the workpiece and violently throw the blade

assembly towards the operator.

e) Never cross your hand over the intended line

of cutting either in front or behind the saw

blade. Supporting the workpiece “cross handed”

i.e. holding the workpiece to the right of the saw

blade with your left hand or vice versa is very dan-

gerous.

f) Do not reach behind the fence with either

hand closer than 100 mm from either side of

the saw blade, to remove wood scraps, or for

any other reason while the blade is spinning.

The proximity of the spinning saw blade to your

hand may not be obvious and you may be seri-

ously injured.

g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence. Al-

ways make certain that there is no gap be-

tween the workpiece, fence and table along

the line of the cut. Bent or warped workpieces

can twist or shift and may cause binding on the

spinning saw blade while cutting. There should be

no nails or foreign objects in the workpiece.

h) Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece. Small debris or loose pieces of wood or

other objects that contact the revolving blade can

be thrown with high speed.

i) Cut only one workpiece at a time. Stacked mul-

tiple workpieces cannot be adequately clamped

or braced and may bind on the blade or shift dur-

ing cutting.

j) Ensure the mitre saw is mounted or placed on

a level, rm work surface before use. A level

and rm work surface reduces the risk of the mitre

saw becoming unstable.

k) Plan your work. Every time you change the

bevel or mitre angle setting, make sure the ad-

justable fence is set correctly to support the

workpiece and will not interfere with the blade

or the guarding system. Without turning the tool

“ON” and with no workpiece on the table, move

the saw blade through a complete simulated cut

to assure there will be no interference or danger

of cutting the fence.

l) Provide adequate support such as table ex-

tensions, saw horses, etc. for a workpiece

that is wider or longer than the table top.

Workpieces longer or wider than the mitre saw ta-

ble can tip if not securely supported. If the cut-o󰀨

piece or workpiece tips, it can lift the lower guard

or be thrown by the spinning blade.

m) Do not use another person as a substitute for

a table extension or as additional support. Un-

stable support for the workpiece can cause the

blade to bind or the workpiece to shift during the

cutting operation pulling you and the helper into

the spinning blade.

n) The cut-o󰀨 piece must not be jammed or

pressed by any means against the spinning

saw blade. If conned, i.e. using length stops,

the cut-o󰀨 piece could get wedged against the

blade and thrown violently.

o) Always use a clamp or a xture designed to

properly support round material such as rods

or tubing. Rods have a tendency to roll while be-

ing cut, causing the blade to “bite” and pull the

work with your hand into the blade.

p) Let the blade reach full speed before contact-

ing the workpiece. This will reduce the risk of the

workpiece being thrown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KZS2000 Primaster Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info