Bedienungsanleitung Scheppach KZS2000 Primaster (Seite 29 von 56) (Deutsch, Englisch, Französisch)

782511

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

GB | 29

• Health hazard due to electrical power, with the use

of improper electrical connection cables.

• Furthermore, despite all precautions having been

met, some non-obvious residual risks may still re-

main.

• Residual risks can be minimised if the „safety in-

structions“ and the „Proper use“ are observed

along with the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the ma-

chine in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the oper-

ating button may not be pressed when inserting the

plug in an outlet.

• Use the tool that is recommended in this manual.

In doing so, your machine provides optimal perfor-

mance.

• Hands may never enter the processing zone when

the machine is in operation.

• Release the handle button and switch o󰀨 the ma-

chine prior to any operations.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair ac-

tive or passive medical implants under certain condi-

tions. In order to prevent the risk of serious or deadly

injuries, we recommend that persons with medical

implants consult with their physician and the manu-

facturer of the medical implant prior to operating the

electric tool.

6. Technical data

AC motor ....................................... 220−240 V~ 50Hz

Power S1 .................................................... 1700 Watt

Operating mode ............................... S6 25%* 2000W

Idle speed n0 ..............................................4700 min-1

Carbide saw blade ..................ø 216 x ø 30 x 2.8 mm

Number of teeth.......................................................24

Maximum tooth width of saw blade ....................3 mm

Swivel range ....................................... −45° / 0°/ +45°

Mitre cut ............................... from 0° to 45° to the left

Saw width at 90° ....................................340 x 65 mm

Saw width at 45°.....................................240 x 65 mm

Saw width at 2 x 45°

(double mitre cut) ...................................240 x 38 mm

Protection class ...................................................II /

Weight ....................................................... ca. 11.9 kg

Laser class ................................................................2

Wavelength of laser ........................................ 650 nm

Laser output ................................................... < 1 mW

* S6, continuous operation periodic duty.

Identical duty cycles with a period at load followed by

a period at no load. Running time 10 minutes; duty

cycle is 25% of the running time.

The work piece must have a minimum height of

3 mm and a minimum width of 10 mm.

Make sure that the workpiece is always secured

with the clamping device.

Noise

Total noise values determined in accordance with EN

62841.

Sound pressure level LpA ........................96.5 dB(A)

Uncertainty KpA ..................................................3 dB

Sound power level LWA ..........................109.5 dB(A)

Uncertainty KWA ................................................. 3 dB

Wear hearing protection.

The e󰀨ects of noise can cause a loss of hearing

The above-mentioned noise emission values were

measured in accordance with a standardised test

procedure and can be used to compare one power

tool with another.

The above-mentioned noise emission values can

also be used for the preliminary assessment of ex-

posure.

Warning:

• The noise emissions during the actual use of the

power tool may di󰀨er from the above-mentioned

values depending on the power tool being used,

in particular on the type of workpiece being pro-

cessed.

• Try to keep emissions as low as possible. For ex-

ample: Limit your working time. In this regard, all

the operational cycle phases must be taken into

consideration (such as the times when the tool is

switched o󰀨 or running idle).

7. Before starting the equipment

• Open the packaging and remove the device care-

fully.

• Remove the packaging material as well as the

packaging and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for trans-

port damage.

• If possible, store the packaging until the warranty

period has expired.

DANGER

The device and packaging materials are not toys!

Children must not be allowed to play with plas-

tic bags, lm and small parts! There is a risk of

swallowing and su󰀨ocation!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KZS2000 Primaster Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info