Bedienungsanleitung Scheppach MT140 (Seite 23 von 52) (Deutsch, Englisch, Französisch)

757078

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

23 І 52

Note: The number of cuts per cutting-off wheel and

their quality may vary considerably with the time tak-

en to make the cuts. Fast cuts may accelerate wheel

wear, but they also prevent discoloring of the work-

piece and the formation of burr.

Quick clamping lever, Fig. 4

The machine is equipped with a quick clamping lever

(6).

Move the lever (6) up, push the clamping handle (5)

forward to the work-piece, push lever (6) down, after-

wards lock the work-piece using the clamping handle

(5).

Attention! Prior to the cutting process, always check

that the work-piece is correctly and securely tight-

ened.

Long work-pieces must be supported by a dolly (roll-

ing support) or similar.

After work completion, place the machine head in the

lower position and pull out the mains plug.

Setting the Cutting wheel depth gauge

The cutting depth of the abrasive Cutting wheel can

be set using the depth cut adjustment screw (15).

Using ring spanner (14), loosen the jam nut.

Adjust the screw counterclockwise to increase the

depth of cut. Tighten the jam nut.

Adjust the screw clockwise to reduce the depth of cut.

Tighten the jam nut.

IX. Technical data

Dimensions L x W x H mm 580 x 310 x 400

Cutting wheel Ø/mm 355 x 25.4 x 3.2

Rated no-load speed 1/min 3000

Weight kg 20

Details for cutting

Workpiece min. mm ø15 or 15x15

Workpiece max. mm ø 100 or 230x50

Drive

Motor V~/Hz 230-240/50

Input power P1 / Watt 2000

Noise

Sound values were measured in accordance with EN

3744 / EN 11201.

Sound pressure level LpA 94.3 dB(A)

Uncertainty KpA 3 dB

Sound power level LWA 107.3 dB(A)

Uncertainty KWA 3 dB

Vibration 2.5 m/s2

Uncertainty K 1.5 m/s2

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Lower the saw head (9) to check whether the cutting

wheel (16) reaches the clamping jaw (7) of the vice.

Retighten the lock nut.

Replacing the cutting-off wheel (See Fig. 5/6)

Pull out the power plug.

Move the machine head (9) to its upper position of

rest.

Swing up the adjustable guard (2) for the cutting-off

wheel and hook it in place by hand.

Open the nut (C) and turn the side guard (E) for the

cutting-off wheel to the rear.

Push the spindle lock (3) to the right and turn the cut-

ting wheel (16) slowly with the other hand until the

spindle lock (3) engages.

Use the supplied wrench (14) to turn out the shaft

screw (D) counterclockwise.

Remove the shaft screw (D), washer, outer ange and

worn cutting-off wheel (16). see Fig.5-6

Install the new cutting-off wheel in reverse order and

tighten.

Important! The parts under the screw (D) have to be

thoroughly cleaned prior to mounting the cutting-off

wheel.

Note the direction arrow!

Use only recommended, reinforced cutting-off

wheels and take care to tighten the shaft screw (D)

just enough to hold the wheel (16) securely in place

and prevent it from spinning. Over-tightening the

shaft screw (D) may damage the cutting-off wheel.

Turn the side guard (E) for the cutting-off wheel back

to the front and fasten in place with the nut (C).

Unhook the guard for the cutting-off wheel, so that

the adjustable guard (2) can be ipped forward again.

VIII. Operation

ON/OFF-switch (See Fig. 1)

Press the lock button (11) and the ON/OFF-switch

(12) to turn on the saw.

To deactivate the cut-off saw again, let go off switch

(12).

Making a cut (See Fig. 3/4)

Clamp the workpiece securely in the vice.

Switch on the machine and wait for the motor to reach

its top speed.

Push down the machine head (9) by the handle (13)

until the cutting-off wheel makes slight contact with

the workpiece.

Move the cutting wheel (16) smoothly through the ma-

terial you want to cut.

Important! Avoid causing the cutting-off wheel to

jump or chatter. This will only result in cuts of poor

quality or a broken wheel.

Press down the handle (13) rmly and evenly during

the cutting operation.

To prevent overheating of the workpiece and ex-

cessive formation of burr, you should not reduce

cutting speed at the end of the cutting operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MT140 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info