Bedienungsanleitung Scheppach MT140 (Seite 25 von 52) (Deutsch, Englisch, Französisch)

757078

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

25 І 52

XIII. Cleaning

m Attention!

Always pull out the mains power plug before starting

any cleaning work.

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts of

the equipment. Ensure that no water can seep into

the device.

XIV. Disposal and recycling

The equipment is supplied in packaging to prevent

it from being damaged in transit. The raw materials

in this packaging can be reused or recycled. The

equipment and its accessories are made of various

types of material, such as metal and plastic. Never

place defective equipment in your household refuse.

The equipment should be taken to a suitable collec-

tion center for proper disposal. If you do not know the

whereabouts of such a collection point, you should

ask in your local council ofces.

XII. Trouble shooting

Trouble Probable cause Solution

Cut-Off saw will not start 1. Tool not plugged in

2. Tripped circuit breaker or blown fuse

3. Power cord damaged

4. Worn or damaged carbon brushes

1. Plug in Cut-Off saw

2. Reset circuit breaker or replace fuse.

3. Have power cord replaced by authorized service center.

4. Replace carbon brushes

Cut-Off saw makes

unsatisfactory cuts

1. Glazed cutting wheel

2. Workpiece incorrectly clamped in vice

1. Replace with a new one.

2. Securely clamp and support workpiece.

Cutting wheel does not

come up to speed

1. Extension cord too light or too long

2. Low voltage from AC power source

1. Replace Cord.

2. Consult certied electrical contractor.

Cut-Off saw vibrates

excessively during cut

1. Saw not mounted securely to work-

bench

2. Damaged Cutting wheel

3. Workpiece incorrectly clamped in vice

1. Tighten all mounting hardware.

2. Replace Cutting wheel.

3. Clamp workpiece securely in vice.

Cut-Off saw does not

make accurate cuts

1. Fence improperly adjusted

2. Cutting wheel not square to fence

3. Excessive force used to make cut

4. Workpiece moving

1. Inspect and adjust fence.

2. Inspect and adjust wheel

3. Reduce pressure on cuts - let wheel do cutting.

4. Clamp workpiece securely in vice.

Material moves during

cutting

1. Fence slipping or workpiece incorrectly

clamped

2. Vice not securely clamping workpiece

3. Excessive force used to make cut

1. Tighten fence.

2. Clamp workpiece securely in vice.

3. Reduce pressure on cuts - let wheel do cutting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MT140 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info