781929
26
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
26
the main switch in the event of an emergen-
cy.
Never clean electrical equipment with water
or similar liquids.
Information for work on hydraulic
equipment:
All work on the hydraulic equipment of the
machine may only be performed by qualified
personnel trained for this purpose as a basic
rule.
Before working, de-pressurise all hydraulic
systems / system parts.
Make sure that suitable collection containers
are available for all materials harmful to
groundwater (oils, coolant, etc.) before
beginning work.
Duties before finishing work
After completion of the service tasks and
prior to starting the machine, the following
points must be observed:
Fill in the test reports, task reports, etc.
Re-check all previously unscrewed
screw connections for firm seating.
Check whether all previous removed
protective devices, covers, container
lids, etc. are properly re-mounted.
Make sure that all tools, equipment
and materials which were used have
been removed from the work area.
Clean the work area and remove any
spilled liquids and similar materials.
Make sure that all the machine's safety
equipment functions properly again.
Test the function of the safety equip-
ment. Do not release the machine for
use if the safety equipment does not
function properly.
Mount and secure the disassembled
protective devices.
Remove all tools, foreign parts and
operating materials left lying around.
Perform a test run with a functional
check of the serviced components.
Secure the machine against unauthor-
ised start-up if you have not completed
the work.
Handling of open flames and smoking
are prohibited.
Maintenance
Cleaning
The conveyor belt should be cleaned thor-
oughly after each use. This will increase the
service life of the machine considerably.
Inspecting the rubber belt
After each use the rubber mats must be
inspected for damage and replaced as neces-
sary.
Check the cable for the cable winch
The cable must be inspected before and after
each use for damage. It may not have any
kinked or crushed areas. Similarly, individu-
al strands may not be broken.
If any damage is present on the cable, it must
be immediately replaced.
Inspect all cable rolls for signs of wear.
Tensioning the conveyor belt
The conveyor belt must be re-tightened
regularly. For this purpose, first loosen the 4
screws (10). Then the upper deflection pul-
ley can be shifted over the two threaded rods
(11).
In the process, always make sure that the re-
tightening takes place to an equal extent on
both sides. Otherwise the conveyor belt
would not longer run in the centre.
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scheppach Muli 4000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info