Bedienungsanleitung Scheppach SC40P (Seite 21 von 71) (Deutsch, Englisch, Holländisch, Französisch)

781423

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 21

Important! Before taking off the grass basket, switch

off the motor and wait until the roller has come to a

stop.

To remove the grass basket, lift up the ejector ap

with one hand, while unhooking the basket with the

other. How frequently you should scarify your lawn

is determined primarily by the speed at which the

grass grows and the hardness of the soil. Keep the

underside of the equipment clean and remove soil

and grass build-up. Deposits make it more dif cult

to start the aerator and decrease the quality of the

scarifying. Always scarify along inclines (not up and

down). Switch off the motor before doing any checks

on the roller.

Important!

The roller rotates for a few seconds after the motor is

switched off . Never attempt to stop the roller. In the

event that the rotating roller strikes an object, immedi-

ately switch off the equipment and wait for the roller to

come to a complete stop. Then inspect the condition

of the roller. Replace any parts that are damaged.

9. Cleaning and maintenance

Danger!

Always pull out the mains power plug before starting

any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents or

solvents; these could attack the plastic parts of the

equipment.

Maintenance

• A worn out or damaged cutting unit should be re-

placed by an authorised expert.

• Take care that all fastening elements (screws, nuts,

etc.) are rmly tightened, so that you can work safe-

ly with the scarier.

• Store the scarier in a dry place.

• For longer life, all screw-fastened parts, such as

wheels and axles should be cleaned and subse-

quently oiled.

• Regular servicing of the scarier not only secures

longer endurance and performance, but also con-

tributes to an accurate and simple scarication of

your lawn.

Starting the equipment

In order to avoid any unintentional start-ups of the en-

gine, it comes equipped with an engine brake (Fig.

1 / Item 1) which must be pressed at all times whilst

the device is in use, otherwise the engine will stop.

Important: When the engine brake lever is released

it must return to its initial position and the engine must

stop. If this is not the case, do not use the equipment

again.

1. Open the petrol cock (Fig. 14 / Item B). Set the

cock to “ON” for this purpose.

2. Set the choke lever (Fig. 14/Item A) to the “Choke”

position. Note: Normally the choke is not required

to restart a warm engine.

3. Move the throttle lever (Fig. 13 / Item 3) to the cen-

tre position.

4. Press the engine brake lever (Fig. 13) and pull the

starter cable (Item 14) forcefully until the engine

starts.

5. Allow the engine to warm up briey and then set

the choke lever (Fig. 13 / Item A) to the “RUN”

Position.

6. The speed of the cutter unit can be controlled us-

ing the throttle lever (Fig. 13 / Item 3).

Important: Always pull the starter cable slowly until

you feel the initial resistance before you then pull it

quickly to start the engine. Do not allow the starter

cable to whip back of its own accord.

Important: The scarier roller begins to rotate as

soon as the engine is started.

Important! Never open the ejector ap when the

motor is running. A rotating cutting unit can cause

injuries. Always fasten the ejector ap carefully. The

ap ips back to the “Closed” position by the tension

springs! Always ensure that a safe distance (provided

by the long handles) is maintained between the user

and the housing. Be especially careful when scari-

fying and changing direction on slopes and inclines.

Maintain a solid footing and wear sturdy, nonslip foot-

wear and long trousers. Always scarify along the in-

cline (not up and down).

For safety reasons, the scarier may not be used to

scarify inclines whose gradient exceeds 15 degrees.

Use special caution when backing up and pulling the

scarier (tripping hazard)!

Tips for proper working

It is recommended that you overlap scarifying paths

a little. Try to scarify in straight lines for a nice, clean

look. In so doing, the aeration swaths should always

overlap each other by a few centimetres in order to

avoid bare strips.

As soon as grass clippings start to trail the scarier, it

is time to empty the grass basket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach SC40P Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach SC40P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info