Bedienungsanleitung Scheppach SM200AL (Seite 18 von 92) (Deutsch, Englisch, Französisch, Italienisch)

781669

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

• Dang er of re from ying sparks !

Grinding metal creates ying sparks. For this rea-

son, always make sure that nobody is placed in any

danger and that there are no inammable materials

near the working area.

Warning! Noxious fumes!

Working with harmful / noxious dusts represents a

risk to the health of the person operating the device

and to anyone near the work area.

• Wear protective glasses, hearing protection, dust

protection mask and protective gloves.

• Dang er of burns! The workpiece gets hot during

grinding. Never touch the part you are grinding. Al-

low the workpiece to cool sufciently rst. When

grinding for longer periods, stop grinding from time

to time and allow the workpiece to cool before con-

tinuing. Do not operate the device for continuous

periods exceeding 10 minutes.

• The double grinding machine is intended for dry

grinding of the surfaces of metal objects. The de-

vice may only be used for dry grinding.

• Do not grind materials containing asbestos. As-

bestos is a known carcinogen.

• Do not use damaged grinding wheels.

• Only use grinding wheels with details that corr

spond with those given on the device ratin plate.

The circumferential speed should be equal to or

greater than the value given on the device rating

plate.

• Adjust the eye guard mounts (spark deectors) and

the eye guards periodically so that wear on the

grinding wheels can be evened out. Keep the gap

as small as possible.

• Avoid contact with the moving grinding wheel.

• Never leave the device working unattended.

• Never use the device for a purpose for which it

was not intended.

• Before you insert the mains plug into the socket,

always check that the device is switched off.

• Always switch the device on before bringing the

workpiece into contact with the grinding wheel. Af-

ter grinding, lift off the workpiece before switching

the device off.

• Hold the workpiece rmly with both hands at all

times when working.

• Always keep proper footing and balance.

• After you have nished grinding metal, allow the

grinding wheel(s) to come to a standstill.

• When taking a break from your work, before car-

rying out any tasks on the device itself and when

you are not using the device, always pull the mains

plug out of the mains socket.

• Handle the device carefully and treat it with re-

spect. Always keep the device clean, dry and free

of oil or grease.

• Remain alert at all times! Always watch what you

are doing and proceed with caution. Do not use

the device if you cannot concentrate or you are

feeling unwell.

• Check before switching on that all spanners, keys

and setting tools have been removed.

17. Avoid unintentionally starting up the device.

• Check that the switch is set to OFF on the device

when the mains plug is inserted into the mains

socket.

18. Using an extension lead for working outdoors.

• When working outside, always use an approved

and appropriately labelled extension lead.

19. Remain alert.

• Watch what you are doing. Proceed with caution. Do

not use electrical power tools if you cannot concen-

trate.

20. Check the electrical power tool for damage.

• Before the electrical power tool is used, carefully

check the safety equipment and any slightly dam-

aged parts to see that they are still working prop-

erly.

• Check that all moving parts on the tool are working

properly, can move freely and are not damaged.

All parts must be correctly attached and full all

the requirements necessary to allow the electrical

power tool to operate properly.

• Damaged safety equipment and components must

be properly repaired or replaced at a competent

electrical equipment repair centre unless other-

wise indicated in the operating instructions.

• Damaged switches must be replaced at a Cus-

tomer Service Centre.

• Never use an electrical power tool that cannot

be switched on and off properly.

21. Caution!

• The use of inserted tools and accessories other

than those recommended by the manufacturer

could lead to you being injured.

22. Have your electrical power tool repaired at an

electrical equipment repair specialist.

• This electrical power tool complies with the rel-

evant safety regulations. Repairs may only be

carried out by a specialist electrical repair centre

using original spare parts, otherwise injury could

occur to the user.

Safety advice relating specically to bench grin-

ders

• Do not touch the mains lead if it becomes dam-

aged or cut through while you are using the device.

Pull the plug out of the mains socket immediately

and have the device repaired by a suitably quali-

ed person or at your service centre.

• Do not operate the device if it is damp and do not

use it in a damp environment.

• If you use the device outdoors, always connect

it through a residual current device (RCD) with a

maximum trip current of 30 mA.If using an exten-

sion lead, always use one that is approved for out-

door use.

• If a dangerous situation arises, pull the mains plug

immediately out of the mains socket.

• Always work with the mains lead leading away

from the rear of the device.

Scheppach SM200AL Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info