Bedienungsanleitung Scheppach SM200AL (Seite 20 von 92) (Deutsch, Englisch, Französisch, Italienisch)

781669

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Work practice

• Exert only moderate pressure on the workpiece so

that it can be machined at constant speed.

• Instead of accelerating your work, high pressure

will cause the drive unit to slow down and even

stop, thus overloading the motor.

• For your own safety, it is essential to secure small

workpieces with a screw clamp or vise.

Grinding

• Place the workpiece onto the workpiece support

(4) and slowly guide the workpiece towards the

grinding wheel (3) at the desired angle to the point

where workpiece and grinding wheel make con-

tact.

• Move the workpiece slightly back and forth to pro-

duce an optimal grinding result. This way the grind-

ing wheel (3) will be evenly worn. Allow the work-

piece to cool down occasionally.

Important!

If the grinding wheel becomes jammed during op-

eration, remove the workpiece and wait until the tool

reaches its top speed again.

Changing the grinding wheels

Important note: In order to prevent injuries from ac-

cidentally starting the machine the machine’s main

switch must be turned off before changing a grinding

wheel. Pull power plug!

• Loosen the spark gard and the eye shield and pull

out as far as possible. Do not remove these parts!

• Loosen work rest and pull out as far as possible.

• Undo the screws of the grinding wheel guard (6)

and remove the guard.

• Take off outside ange and the old grinding wheel,

then assmeble the new one.

Important note:

• Do not remove the pieces of card board on the

sides of the wheel, as they are intended for

strengthening the grip of the Flange against the

grinding wheels.

• Examine the new grinding wheels on cracks or

other visible damages and dispose if necessary.

• Mount ange and nut again.

• Do not tighten the screw by force. This can cause

the grinding wheel to break.

• Re-install the grinding wheel guard (6) in the re-

verse order.

• Mount work rest, spark guard and eye shield ac-

cording to installation instructions.

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• The grinding wheels must rotat freely.

• Check that the voltage on the rating plate is the

same as your supply voltage before you connect

the equi ment to the power supply.

Warning! Never connect the plug to power source

outlet until all installations and adjustments are com-

pleted and you have read and understood sthe safety

and operation instructions.

Tool support (left and right) (Fig.1+Fig. 2+2.1)

Fasten the tool support (4) to the grinding wheel

guard (6) with the wing screw (a) and washer (b).

The distance between wheel and work rest should

not exceed 2 mm.

Spark guard with LED work lamp (left and right)

(Fig.1+Fig.3)

Fasten the spark guard (2) with LED work lamps (5)

to the grinding wheel guard (6) with two M5x8 pan

head screws (c).

The distance to the grinding wheel (3) should be not

more than 2mm. The distance between the spark

guard (2) and the grinding wheel (3) can be adjusted

by slackening the two pan head screws (c). Tighten

the screws securely.

LED work lamp (Fig.1+Fig. 4+Fig.4.1+Fig.4.2)

The lighting (5) can be switched on by pressing the

switch (d) on the lamp. The lighting is switched off

by pressing the switch again.

Open the battery compartment (Fig. 4.1) to insert/

change the batteries (2xAAA R03 1.5 V) . Insert the

batteries (2x on each side) (Fig. 4.2). If you change

the batteries dispose of the used batteries properly.

Replace the cover of the battery compartment in re-

verse order (Fig 4.1).

Safety screens (Fig. 1+Fig.5+Fig.5.1)

Install the safety screen (1) on the LED work lamp (5)

with the M5x55 mushroom head screw (e) and the

knurled head screw (f).

The guard is individually adjustable, as to protect the

users eyes during grinding process.

8. Operation

On/Off switch (8)

• To switch on the equipment set the On/Off switch

(8) to position On.

• Move the On/Off switch (8) to position Off to switch

off the equipment.

After switching on, wait for the equipment to reach

its maximum speed of rotation. Only then should you

begin with the grinding.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach SM200AL Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info