Bedienungsanleitung Scheppach SM200AL (Seite 19 von 92) (Deutsch, Englisch, Französisch, Italienisch)

781669

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Load factor:

A load factor of S2 10 min (intermittent periodic duty)

means that you may operate the motor continuously

at its nominal power level (500 W) for no longer than

10 minutes ON period. If you fail to observe this time

limit the motor will overheat. During the OFF period

the motor will cool again to its starting temperature.

Sound and vibration

Sound and vibration values were measured in

accordance with EN 61029.

LpA sound pressure level 62,4 dB(A)

KpA uncertainty 3 dB

LWA sound power level 77 dB(A)

KWA uncertainty 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions)

determined in accordance with EN 61029.

Vibration emission value ah ≤ 2.5 m/s2

K uncertainty = 1.5 m/s2

Warning!

The speci ed vibration value was established in ac-

cordance with a standardized testing method. It may

change according to how the electric equipment is

used and may exceed the speci ed value in excep-

tional circumstances.

The specied vibration value can be used to com-

pare the equipment with other electric powertools.

The specied vibration value can be used for initial

assessment of a harmful effect.

Keep the noise emissions and vibrations to a

minimum.

• Only use appliances which are in perfect working-

order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

7. Assembly

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

Always pull the power plug before making

adjustments to the equipment.

Pull the power plug before doing any mainte-

nance or assembly work on the equipment.

• The machine must be set up so that it stands rm-

ly, i.e. it must be securely screwed to a work bench

or similar.

• Store grinding wheels in such a way that they are

not subject to mechanical loads or damaging en-

vironmental inuences.

• Do not use damaged or unshaped wheels.

• The adjustment of the spark guard shall be made

frequently, so as to compensate the wear of the

wheel, keeping the distance between the guard and

the wheel as small as possible, and no greater than

2 mm.

• The adjustment of the work rest shall be made fre-

quently, so as to compensate the wear of the wheel,

keeping the distance between the work rest and the

wheel as small as possible, and no greater than 2

mm.

• Use wheels that have a bore exactly equal to the

arbor of the grinder. Do not attempt to machine an

undersized wheel to t an arbor.

• Do not overtighten wheel nut.

• Do not grind on a cold wheel. The grinding wheel

should be started and run at idle speed for one

minute before applying the work.

• Do not grind on the side of the wheel. Grind on the

face of the wheel only.

• Do not apply coolant directly to a grinding wheel.

Coolant can weaken the bonding strentgh of the

wheel and cause it to fail.

• Sparks are a hazard. Do not grind near gas or

ammable liquids.

• Stand to one side of the wheel when turning on the

power. Dress the wheel on the face only. Dressing

the side of the wheel can cause it to become too

thin for safe use.

• Grinding creates heat. Do not touch the work piece

until you are sure it has cooled down sufciently.

• Use grinding wheels that are rated for safe use on

the grinder. Do not use a wheel that is rated lower

than the grinder speed.

6. Technical Data

Delivery

Bench Grinder

User’s Manual

Technical Data

Dimensions L x W

x H mm 410x260x290

ø grinding disc

max. mm left/right 200/200

ø grinding disc

min. mm left/right

(after wear and

tear)

160

ø grinding disc

bore max. mm 15,88

grinding disc

width mm left/right 20/40

Lamp LED with battery (2x)

Weight kg 13

Motor

Motor V/Hz 230-240/50

Input power

S2 10 min W 500

Motor speed 1/min 2850

Subject to technical changes!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach SM200AL Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info