Bedienungsanleitung Scheppach TS2800 Primaster (Seite 26 von 48) (Deutsch, Englisch, Französisch)

782536

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

26 І 48

4 Do not use any insertion tools with cracks. Sort

out cracked insertion tools. Repairs are not per-

mitted.

5 Clean grease, oil and water off of the clamping

surfaces.

6 Do not use any loose reducing rings or bushes

for the reducing of holes on saw blades.

7 Make sure that xed reducer rings for securing

the insertion tool have the same diameter and

have at least 1/3 of the cutting diameter.

8 Make sure that xed reducer rings are parallel

to each other.

9 Handle insertion tool with caution. They are ide-

ally stored in the originally package or special

containers. Wear protective gloves in order to im-

prove grip and to further reduce the risk of injury.

10 Prior to the use of insertion tools, make sure that

all protective devices are properly fastened.

11 Prior to use, make sure that the insertion tool

meets the technical requirements of this electric

tool and is properly fastened.

12 Only use the supplied saw blade for sawing oper-

ations in wood, materials similar to wood, plastics

and non-ferrous metals (except for magnesium

and alloys containing magnesium).

6. Remaining hazards

The machine has been built according to the state of

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use

of improper electrical connection cables.

• Furthermore, despite all precautions having been

met, some non-obvious residual risks may still re-

main.

• Residual risks can be minimised if the „safety in-

structions“ and the „Proper use“ are observed

along with the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the ma-

chine in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the op-

erating button may not be pressed when inserting

the plug in an outlet.

• Use the tool that is recommended in this manu-

al. In doing so, your saw provides optimal perfor-

mance.

• Hands may never enter the processing zone when

the machine is in operation. Release the handle

button and switch off the machine prior to any op-

erations.

• Prior to any adjustment, maintenance or service

work disconnect the mains power plug!

–Use the upper blade guard and set it to the cor-

rect position.

–Only use saw blades for which the maximum per-

missible speed is not lower than the maximum

spindle speed of table saws and which are suit-

able for the material to be cut.

–Do not cut rebates or grooves without tting a

suitable guard, e.g. a tunnel-type guard, over the

saw table.

–Circular saws must not be used for slotting jobs

(cutting grooves which end in the workpiece).

–When transporting the electric tool, only use the

transport devices. Never use the protective de-

vices for handling or transport.

–Make sure that the upper part of the saw blade is

covered during transport, e.g. by the protective device.

–Be sure to only use spacers and spindle rings

specied by the manufacturer as suitable for the

intended purpose.

–The oor around the machine must be level, clean

and free of loose particles, such as chips and

cutting residues.

–Always stand to the side of the saw blade when

working with the saw.

–Do not remove any cutting residues or other parts

of workpieces from the cutting zone while the

machine is running and the saw unit is not at rest.

–Make sure that the machine is always secured on

a workbench or a table if at all possible.

–Support long workpieces (e.g. with a roller table)

to prevent them sagging at the end of a cut.

–m Attention! Never remove loose splinters, chips

or jammed pieces of wood while the saw blade is

running.

• Switch off the machine to troubleshoot or remove

jammed pieces of wood. - Disconnect the main

power plug -

• Retting, including adjusting and measuring

works, and cleaning must be carried out only

when the motor is switched off. - Disconnect the

main power plug -

• Before switching on again, ensure that keys and

adjustment tools have been removed.

Warning! This electric tool generates an electro-

magnetic eld during operation. This eld can impair

active or passive medical implants under certain

conditions. In order to prevent the risk of serious or

deadly injuries, we recommend that persons with

medical implants consult with their physician and the

manufacturer of the medical implant prior to operat-

ing the electric tool.

Safety instructions for the handling of saw blades

1 Only use insertion tools if you have mastered

their use.

2 Observe the maximum speed. The maximum

speed specied on the insertion tool may not be

exceeded. If specied, observe the speed range.

3 Observe the motor / saw blade direction of rota-

tion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach TS2800 Primaster Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info