Bedienungsanleitung Scheppach TS2800 Primaster (Seite 29 von 48) (Deutsch, Englisch, Französisch)

782536

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

29 І 48

Cutting narrow workpieces, Fig. 25

Be sure to use a push stick when making longitudinal

cuts in workpieces smaller than 120 mm in width. A

push block is supplied with the saw! Replace a worn

or damaged push stick immediately.

• Adjust the parallel stop to the width of workpiece

you require.

• Feed in the workpiece with two hands. Always use

the push stick in the area of the saw blade.

• Always push the workpiece through to the end of

the splitter.

Caution! With short workpieces, use the push stick

from the beginning.

Cutting edges and strips, Fig. 26

Operating cycle: Mount the fence with a low stop bar

surface or use an auxiliary fence. Feed the work-

piece with a push-stick until the end of the workpiece

is in the region of the riving knife. Prevent long work-

pieces from toppling over at the end of the cutting

process by using a table length extension.

Making cross cuts, Fig. 27

Operating cycle: Adjust the rejection rail so that

workpiece sections do not touch the ascending part

of the sawblade. Only feed the workpiece by means

of a crossfeed stop or a cross slide.

Do not remove wood chippings from the region of the

workpiece with your hands.

11. Cleaning and Maintenance

Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

down with compressed air at low pressure.

• We recommend that you clean the equipment im-

mediately after you use it.

• Clean the equipment regularly with a damp cloth

and some soft soap. Do not use cleaning agents

or solvents; these may be aggressive to the plastic

parts in the equipment. Ensure that no water can

get into the interior of the equipment.

• In order to extend the service life of the tool, oil

the rotary parts once monthly. Do not oil the motor.

12. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C.

Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

In times of non-use keep the push stick or the push

block with the electrical power tool at all times.

Saw Blade – Diagonal Adjustment

• The saw blade may be swiveled from 90° to 45° after

the wing nut has been loosened.

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions.

Readjust the angle adjustment on the adjusting bolts 1

& 2.

Saw Blade Height Adjustment

The saw blade is adjustable from 0 to 83 mm cutting

height after the wing nut has been loosened.

For safe and clean working, choose a minimal saw

blade projection for the workpiece.

Dem Spaltkeil wie im Bild 22 gezeigt einstellen.

Adjust the riving knife as shown in picture 22.

The riving knife is an important safety device which

guides the workpiece and prevents the cutting joint from

closing behind the saw blade and the workpiece from

being kicked backwards. Check the riving knife thick-

ness. The riving knife should never be thinner than the

body of the saw blade or thicker than the cutting joint

width.

Only use saw blades with a diameter of 315 mm and a

thickness of 2.4 mm (3.0 mm teeth).

Lower the suction hood onto the workpiece during every

working cycle. The hood must be positioned horizon-

tally above the saw blade during every working cycle.

Length Cuts

Insert the length stop for parallel cuts.

Use the stop ruler with the high stop side for cuts above

120 mm and the stop ruler with the low stop side for cut

widths under 120 mm.

Lead the workpiece with the push stick.

Diagonal Cuts

For diagonal and angle cuts, insert the cross-cutting

guide.

Operational Information

Working on circular saws

Cutting wide workpieces, Fig. 24

Width of the workpiece to be machined over 120 mm

Operating cycle: Adjust the ripping fence in accordance

with the width of the workpiece. Ensure that your hands

are resting in a safe place. The workpiece may only be

forward-fed in the tool area with the right hand or with

the aid of a push-stick if narrow workpieces are cut off

in the cutting process. Move the fence back to the mid-

dle of the saw or use a short auxiliary fence if there is

a danger of the workpiece being jammed between the

circular sawblade, the riving knife and the fence.

Only the upper suction hood has been left out in the

individual case in order to display the operating cycle or

device more clearly.

The upper suction hood is required for all of the operat-

ing cycles.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach TS2800 Primaster Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info