Bedienungsanleitung Scott BMX - 2014 (Seite 6 von 15) (Englisch)

664187

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

10 scott-sports.com 11

BMXENGLISH

BIKE OWNER’S MANUAL

Remove the shoe fixing pin.

Insertion of shoe fixing pin is very critical to keep shoe properly fixed in place.

Remove the shoe by sliding it along the groove of the shoe holder.

There are two different types of shoe and shoe holder to be used

in the left and right positions respectively. Slide the new shoes into the grooves

on the shoe holders while taking note of the correct directions and pin hole

positions.

Shoe

insertion

direction

for the left

for the right

same at front and rear

front

shoe holder

shoe

shoe fixing pin

Replacement of the brake pads/cartridge shoe

Remove the security pin on the brake shoe.

1. Remove the brake pad by sliding it along the groove of the brake shoe bar.

2. Make sure to use the correct brake pad and brake shoe for each side.

Those for the left side are different from those for the right side.

3. Slide the new pad into the shoe and make sure that the direction is correct and

that the security pin holes concord.

4. The insertion of the security fixing pin is very important. It keeps the shoe

properly in place

Remove the shoe fixing pin.

Insertion of shoe fixing pin is very critical to keep shoe properly fixed in place.

Remove the shoe by sliding it along the groove of the shoe holder.

There are two different types of shoe and shoe holder to be used

in the left and right positions respectively. Slide the new shoes into the grooves

on the shoe holders while taking note of the correct directions and pin hole

positions.

Shoe

insertion

direction

for the left

for the right

same at front and rear

front

shoe holder

shoe holde

shoe

shoe fixing pin

Rim and wear of the rim

If the brake system has brake pads, you have to be aware of the fact that the rim will be

worn through the action of braking.

When riding in wet and muddy terrain for example, the rim is quickly worm out.

Small cracks in the brake surface of the rim or a deformation of the brake surface on

the rim when increasing the tire pressure point out the end of the lifetime of the rim

and the rim should be replaced immediately at an authorized dealer.

SCOTT bikes that are fully equipped (lights, mudguard, carrier) have a wear-out-

indicator.

Please follow the instructions of the rim manufacturer shown in a manual or on the rim

itself.

Tires should always be inflated within the manufacture’s recommendations.

They are rated from 40 to 80 lbs. (check your tires).

Higher pressure for smoother roads or heavy riders.

Lower pressure for more shock absorption on rougher terrains.

Please find following example:

INFLATE TO MIN. 3.5 (50PSI) - MAX. 6.0 BAR (85PSI)

TIRES AND RIMS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scott BMX - 2014 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scott BMX - 2014

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info