Bedienungsanleitung Seat Leon 2024 (Seite 359 von 406) (Englisch)

817342

359

Zoom out

Zoom in

Vorherige Seite

1/406

Nächste Seite

Wheels and tyres

357

Tyre pressure monitor system

Tyres with directional tread pattern

Tyres with directional tread pattern have been

designed to operate best when rotating in only

one direction. An arrow on the tyre sidewall in-

dicates the direction of rotation on tyres with

directional tread. Always observe the indicated

direction of rotation in order to guarantee opti-

mum grip and help avoid aquaplaning, exces-

sive noise and wear.

If the tyre is mounted in the opposite direction

of rotation, drive with extreme caution, as the

tyre is no longer being used correctly. This is

of particular importance when the road surface

is wet. Change the tyre as soon as possible or

remount it with the correct direction of rotation.

Works after changing a wheel

●Replace the hub caps or wheel bolt caps

(depending on equipment).

●Return all tools to their proper storing loca-

tion.

●If the replaced wheel does not ﬁt in the spare

wheel housing, store it safely in the luggage

compartment ›››page282.

●Check the tyre pressure of the newly moun-

ted tyre as soon as possible.

●In vehicles ﬁtted with a tyre pressure indica-

tor, adjust the pressure and store it in memory

›››page357.

●Have the tightening torque of the wheel nuts

checked as soon as possible with a torque

wrench ›››page356. Meanwhile, drive care-

fully.

●Have the ﬂat tyre replaced as quickly as pos-

sible.

Tyre pressure monitor sys-

tem

Tyre pressure monitor indicator

Fig.250 Instrument cluster: warning of loss of

tyre pressure.

The tyre pressure monitoring system compares

the individual speeds of each wheel and thus

the dynamic radius with the help of the ABS

sensors.

If the rolling circumference of one or more

wheels has changed, the tyre pressure monitor-

ing indicator will indicate this on the instrument

panel through a warning lamp and a warning to

the driver ›››Fig.250. If only one tyre is aec-

ted, its position on the vehicle will be indicated.

Loss of pressure: Check left tyre

pressure!

Change in wheel diameter

The wheel diameter changes when:

●Tyre pressure is changed manually.

●The tyre pressure is insucient.

●The tyre's structure is damaged.

●The vehicle is not level due to a load.

● The wheels on an axle are subject to a heav-

ier load (e.g. with a heavy load).

●The vehicle is ﬁtted with snow chains.

●The temporary spare wheel is ﬁtted.

●One wheel has been changed on an axle.

There may be a delay in the reaction of the tyre

pressure monitoring indicator or it may not

indicate anything under certain circumstances

(e.g. sporty driving, snow-covered or unpaved

roads, or when driving with snow chains).

Calibrate the tyre pressure monitoring indi-

cator

After changing the tyre pressure or replacing

one or more wheels, the tyre pressure monitor-

ing indicator must be recalibrated. This should

also be done, for example, when switching the

front and rear tyres.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seat Leon 2024 Seite 359

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Seat Leon 2024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info