758983

Sencor SPR 4000 Seite 13

13
Zoom out
Zoom in
Vorherige Seite
1/14
Nächste Seite
- 13 - 06/2019
Copyright © 2019, Fast ČR, a.s.
■
Press the latch F1 of the steam release valve cover and open up
the cover. Wash both parts of the cover, including the safety float
valve indicator A8 in warm water with detergent, rinse and dry
them thoroughly. Assemble the cover and return it back into the
pressure cooker lid.
Attention:
Before connecting the power cord into apower socket
and into the pressure cooker and before turning the
pressure cooker on again, allow all surfaces to cool
down completely.
PROBLEM POSSIBLE CAUSE REMEDY
The pressure
cooker cannot be
turned on.
The power is not
connected
Check the connection of
the power cord, plug and
the power socket.
The pressure
cooker lid cannot
be closed and
locked
The gasket of the
inner pot lid is not
seated correctly.
Check the correct position
of the gasket.
The safety float valve
indicator or the safety
valve itself is in the up
position.
Using asuitable tool
(e.g.skewer) push the
indicator and/or the valve
into the down position.
The lid of the
pressure cooker
cannot be
opened.
There is still pressure
inside the pressure
cooker.
Release the pressure from
inside the pressure cooker
using button B4 (Add
ingredients).
The pressure
cooker lid cannot
be opened
after the steam
has been fully
released.
The safety float
valve is still in the up
position.
Using asuitable tool (e.g.
skewer) push the valve
into the down position.
Alarge amount
of steam is
escaping around
the edge of the
pressure cooker.
The pressure cooker
lid is not properly
closed.
Check the correct
installation of the gasket
in the lid.
The inner pot lid
gasket is not in its
place or is soiled by
food remains.
Position the gasket
correctly on the lid or
clean it.
The inner pot lid
gasket is worn out or
damaged
Replace the damaged
gasket with anew one of
the same type.
The inner pot lid is
damaged or deformed
(e.g. by falling on the
floor).
Contact the service
department.
Alarge amount
of steam is
escaping from
the safety float
valve A5.
There are food
remains on the inner
pot lid gasket.
Remove the gasket from
the lid and clean it
The inner pot lid
gasket is worn out or
damaged
Replace the damaged
gasket with anew one of
the same type.
Steam is
continuously
escaping from
the steam valve.
Steam valve fault. Contact the service
department.
The hotplate is
not heating.
The pressure cooker
lid is not properly
closed.
Close the lid in the proper
manner.
The hotplate is faulty
or the power circuit is
defective.
Contact the service
department.
Code E1 is lit on
the display. Faulty bottom sensor. Contact the service
department.
Code E2 is lit on
the display.
The temperature of
the bottom sensor is
too high.
Disconnect the power
supply and after the
pressure cooker cools
down, reconnect it. If
the fault does not go
away, contact the service
department.
Code E2 is lit on
the display.
Interrupted circuit of
the bottom sensor.
Contact the service
department.
Code E6 is lit on
the display.
Interrupted circuit of
the pressure cooker lid
sensor.
Contact the service
department.
Code C1 is lit on
the display.
Overheating
protection was
engaged.
Check whether there is
asufficient amount of
food and water inside
the pot and fill it up if
necessary. Then press B2
(Cancel/Keep warm). If the
code does not disappear
even after this, disconnect
the power supply and
after the pressure cooker
cools down, turn it on
again. If the malfunction
persists, contact the
service department.
Code E8 is lit on
the display.
The pressure switch
circuit is interrupted.
Contact the service
department.
Rice or food is
half cooked or
too hard.
Not enough water. Add water.
The pressure cooker
lid was opened
prematurely.
When the cooking cycle
has finished, leave the
lid closed for 5 minutes
or more.
Frozen food was
placed into the inner
pot.
Allow frozen food to
defrost before cooking it.
Rice is too soft. Too much water. Reduce the amount of
water.
There is water
behind the
pressure cooker.
The condensate tank
is full or condensate
water is dripping
down the surface of
the pressure cooker
unit.
Empty out the condensate
tank or select adifferent
location for the pressure
cooker so that steam has
more space above itself.
Wipe away the water.
The pressure
cooker is
emitting an
unpleasant
odour.
There are food
remains or other
materials on the outer
surface of the inner
pot or on the hotplate.
Check and if necessary
clean the contact surfaces
of the inner pot and the
hotplate.
STORAGE
■
Before storing it, the pressure cooker must be completely cool,
clean and dry.
■
Disconnect the plug of the power cord from the socket of the
pressure cooker.
■ Insert the removable inner pot A10 into the built-in outer pot A11.
The accessories A16 to A19 can be placed inside the inner pot A10.
■
If your storage space permits, it is recommended to keep the lid
A1 open to enable the inside of the pressure cooker to ventilate.
■
Place the pressure cooker in aclean, dry place out of reach of children.
Attention:
Keep the stored pressure cooker away from extreme
temperatures, direct sunlight and excessive humidity
and do not store it in an overly dusty environment. Do
not place anything on to the pressure cooker.
TECHNICAL SPECIFICATIONS
Rated voltage range ...................................................................... 220−240 VAC
Rated frequency ........................................................................................50/60 Hz
Power output ................................................................................................1 100 W
Capacity of the pressure cooker .......................................................................4 l
Pot dimensions.................................................................... 310 x 285 x 450 mm
Operating pressure ....................................................................................... 70 kPa
Temperature range ................................................................................. 30-160 °C
Weight ................................................................................................................ 6.7 kg
Protection class .................................................................................................. IPX0
… 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sencor SPR 4000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info