- 10 - 08/2020
Copyright © 2020, F
CONTROLLING
APPLICA
The vacuum cleaner can also be controlled using a smartphone or tablet.
application enables you to select the cleaning mode, stop the cleaning process or
send the vacuum cleaner to the charging station; it pro
time was spent cleaning and about the condition of the vacuum cleaner
The application is freely available in the Apple App S or Google Play Store. The
link for this application is found in the picture part of this user'smanual.
Note:
The robotic vacuum cleaner supports W
If unsure about which standards are used by your
router
of the router
After downloading and installing the application on to asmart device, set the vacuum
cleaner into the network configuration mode by pressing and holding down butt
A2 until aA2 will start flashing slowly. If you
wish to cancel the network configuration mode, press buttA2 on the vacuum
cleaner or C4 on the remote control.
Launch the application. After registration, the application will guide you thr
process for connecting the vacuum cleaner to your
CHARGING
AUT
When the vacuum cleaner finishes cleaning or when it detects alow batter
during operation, the indicator in button A2 will start flashing read and the vacuum
cleaner will automatically start to seek out the charging station.
In order for it to find it and dock, it needs to find the infrared signal transmitted
by the charging station. F
station constantly connected to the power grid and locat
instructions provided in chapter L
In the event that the vacuum cleaner is for some reason unable to find the char
station (too many obstacles, incorrect location, etcA2 will
start flashing red. In this case, it is necessary to place the vacuum cleaner near the
charging station or directly on to its contacts.
After docking in the charging station, the charging cycle will commence. Afull char
takes approximately 5 hours.
the battery. Afully charged battery will provide up to 90 minutes of oper
During the charging process, the indicator lighA2 will flash white. When the
battery is fully charged, the indicator lights on both buttons will remain permanently
lit white and the process will end automatically
In the event that the charging contacts are disconnected during the charging cycle,
the vacuum cleaner will move away fr
to resume the charging process
the event of apower outage, the charging cycle will be interrupted and will c
after the power supply is renewed. In the event tha
exceeded, the charg will automatically interrupt the charging cycle.
MANUAL CHAR
If the vacuum cleaner is located away from the charg low
battery voltage then the indicator in button A2 will start flashing red. Press button C2
on the remote control.
station and start automatic charging as described in the previous chapter
If the battery is so flat that the vacuum cleaner is unable to seek out the charging
station then it is necessary to dock the vacuum cleaner into the charging station by
hand. Pick up the vacuum cleaner and manually place it into the char
that the charging contacts on the underside of the vacuum cleaner and the charging
contacts on the charging station are connected.
charging will start.
CARING FOR THE BA
We rec
in acharged state.
Do not leave the vacuum cleaner completely flat f
time. Abattery that is allowed to remain flat for along time may self-discharge below
apermissible level and thereby cause irreparable damage to itself
REPLACING THE BA
Make sure that the vacuum cleaner is turned off with the main switch A7 . T
vacuum cleaner upside down and remove the scrA14 .
T
Disconnect the battery and take it out. Connect a new batter and place it into the
battery compartment being careful not to damage the connector cables. Screw the
battery cover back on.
Attention:
Use only the original battery type.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE AND SOL
The vacuum cleaner
cannot be turned on.
The battery is almost or completely flat, and it is necessary
to charge it. Manually place the vacuum cleaner on to the
charging station.
The vacuum cleaner
is running but it is
vacuuming dust and
dirt poorly or not at all.
The dust container is full. Empty it out.
The dust filter in the container is not properly installed or
is excessively soiled. Check the position and cleanliness of
the filter
The central rotary brush is clogged with material or hair is
tangled on it, and it is not turning. Clean out the brush and
the suction hole.
The vacuum cleaner
is making an unusual
noise while cleaning.
The central rotary brush, side rotary brushes or one of the
motorised wheels is wrapped with material or tangled into
an obstacle (cables, etc.).
The vacuum cleaner
travels only backwards
when it is turned on.
The vacuum cleaner was placed on afloor that is too dark.
Move the vacuum cleaner to alighter-coloured floor and
start it again.
One of the bottom sensors is soiled. Clean the all the sensors.
The bristles on arotary
brush are deformed
and do not sweep up
dust and dirt.
The bristles are worn out. Dip them in warm water to r
their original shape. Contact the vendor or service centre and
order anew brush.
Cleaning at
ascheduled time
didnot occur
The battery was not sufficiently charged. Scheduled cleaning
will only start when the battery is charged to at least 30%.
The vacuum cleaner was turned off using the main switch.
After performing scheduled cleaning, it must be in the stand-
by or sleep mode.
The vacuum cleaner
did not travel on to the
charging station.
The charging station is not connected to mains pow
Connect it.
The vacuum cleaner is too far away fr
station. Carry the vacuum cleaner by hand to the vicinity of
the charging station.
The charging station is not located acc
instructions in this user'smanual and the vacuum cleaner has
poor access to it.
The vacuum cleaner is
in the charging station
but is not charging.
Check that the charging station is connected to the power
grid. Clean the charging contacts on the charging station and
the vacuum cleaner
Check that the main power switch is in the ON position.
The vacuum cleaner
did not connect to the
Wi-Fi network.
Weak
its range.
Incorrectly entered password.
Y
vacuum cleaner can only receive signals in the 2.4 GHz
broadcast band.
Indicator of button A2
is flashing red
The control system of the vacuum cleaner has det
aproblem, that may include the vacuum cleaner being lifted
off the ground, the dust container / wat
the vacuum cleaner during the charging process, the wheels
or brushes becoming blocked during operation, etc. Attempt
to identify what has caused the problem and attempt to fix it.
If the red flashing persists, try turning off the vacuum cleaner
using the main switch A7 and turn it back on after at least
20seconds. If even this fails to help
service centre.
CLEANING AND MAINTENANCE
Prior to cleaning, alwayA7
to the OFF position.
For cleaning, nev
Neglecting cleaning and maintenance may negatively affect the working order of the
vacuum cleaner and lead to its reduced performance.
Attention:
When turning the vacuum cleaner upside down for maintenance
tasks, ensure that it does not fall out of your hands on to the floor
or that you do not damage its camera A5 when putting it down.
We rec
surface.
DUST CONT
Empty out the dust container after every use and clean it regularly.
Pressing latch E1 , slide out the dust container A6 fr
awaste basket, garbage bin, etc.
Press latch E6 to open the bottE5 and tip out the dirty material. For hygiene
reasons, we rec
Open the cover E4 and take it out of the holder with the dust filter E3 .
filter and its holder or clean these parts using the brush E2 . Check the condition of the
filter and if damaged, replace it with anew one.
In the event of greater soiling, the dust c
washed under running water
components to dry completely.
