Do not wash the dust container or the dust filter in adishwasher.
Before putting the vacuum cleaner back into operation, check
that the dust filter is in its location. Otherwise the vacuum cleaner
may be damaged.
■Assemble all the parts to the initial state and slide the dust container back into the
vacuum cleaner.
WATER TANK
■We recommend that water is poured out of the water tank A4 and the tank is cleaned
after every wiping of the floor.
■Press latch D1 to slide the water tank out from the vacuum cleaner and then remove
the holder D3 with the mop fabric D4 from the water tank.
■Flip open the rubber cap D2 and pour out any remaining water.
■Use adamp cloth to wipe the entire tank and allow it to dry naturally. Do not expose
the water tank to direct sunlight while drying it.
Attention:
Do not wash the water tank, holder or mop fabric in adishwasher.
MOP
■After every dry or wet wiping, remove the mop fabric from the holder, wash it by hand
in lukewarm water with the addition of asmall amount of gentle washing powder and
allow it to dry naturally.
■Wipe the mop holder with alightly dampened cloth or wash it under running water
and then dry thoroughly.
CENTRAL ROTARY BRUSH
■Push on the latches F1 of the central rotary brush cover A21 and take out the cover.
■Take out the rotary brush A22.
■Use adry wiping cloth to clean out the area in which the rotary brush is housed. Also
clean the suction hole, the procedure is described later in this user'smanual.
■Remove any dirt and material (dust, wound on hair, animal fur, etc.) from the brushes
F2 of the rotary brush and also from the ends F3. You can cut heavily wound on hair
using the blade of the cleaning brush E2.
■Reinsert the rotary brush and its cover.
Attention:
In the event that an excessive amount of dirty material
accumulates on the central rotary brush and in its compartment,
there is arisk of permanently damaging the vacuum cleaner.
Regularly inspect the condition of the brush.
Do not use the vacuum cleaner without the central rotary brush.
SUCTION HOLE
■The suction hole is located underneath the central rotary brush, therefore, take it out
before cleaning the suction hole as described in the previous chapter. With repeat
use, dust and dirt may accumulate around the suction hole, which may manifest itself
through decreased suction efficiency. Remove the dirt and dust from the suction
hole using asoft brush. Regularly clean the suction hole to ensure maximum suction
power.
SIDE ROTARY BRUSHES
■Take out the rotary brushes by pulling them upwards. Remove any dust and dirt from
the location where the brushes were mounted.
■Remove all dust and dirt from the brushes. If necessary you may wash the brushes
under running water. If the bristles were deformed while the vacuum cleaner was
running, dip them in warm water to allow them to return to their original shape. Allow
the brushes to dry before reattaching to the vacuum cleaner.
■After cleaning it, reattach it.
Note:
The rotary brushes become worn out when used. After acertain time it
is necessary to replace the used brushes with new ones. To order new
brushes, contact your vendor or an authorised service centre.
COMPLETE ROBOTIC VACUUM CLEANER
■Regularly wipe the surface of the vacuum cleaner using asoft dry wiping cloth.
■First remove any coarser dirty material from the front swivel wheel A18 and the
motorised wheels A13 and A20. Then clean them around their entire perimeter using
alightly dampened cloth and wipe them dry. Do not forget to also clean the area
around the wheels.
■At least once per week, or more often, wipe the sensors A9, A12, A19 on the
underside of the vacuum cleaner and the side sensor A8 using asoft dry wiping cloth
or acotton bud.
CHARGING STATION
■At least once per week, clean the surface of the charging station B1 including the
charging contacts B2 using asoft dry wiping cloth.
STORAGE
When not using the vacuum cleaner for an extended period of time, do the following:
■Turn off the vacuum cleaner by setting the main switch to the OFF position.
■Clean the vacuum cleaner as described in chapter CLEANING AND MAINTENANCE.
■Disconnect the charging station from the power socket.
■Store the vacuum cleaner with all its accessories in adry, clean and cool place.
TECHNICAL SPECIFICATIONS
Robotic vacuum cleaner
Dimensions (diameter × height) ......................................................................................340 × 90 mm
Weight ...........................................................................................................................................................3 kg
Motor power output ..............................................................................................................................40 W
Operating time per single charge.....................................................................................up to 90 min
Dust container capacity ....................................................................................................................250 ml
Water tank capacity ............................................................................................................................350 ml
Vacuuming system .......................................................................................SUPER SUCTION 4 000 Pa
Navigation system ..........................................................................................................Sencor Nav. 16.0
Power adapter
Input ..........................................................................................................100–240 VAC, 50/60 Hz, 0.2 A
Output..........................................................................................................................................5 V, 1000 mA
Battery
Type ......................................................................................................................................2,600 mAh Li-Ion
Charging time ..........................................................................................................................................4–6 h
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Sencor SRV 8550 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
