Bedienungsanleitung Sharp HT-SB100 - Soundbar (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

787657

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Accessories

• Remote control (inc. batteries)

• Power cable

• Wall mount brackets

• Wall mount xings (screws and plugs)

• Silicone rubber feet

• User documentation

Controls

(Refer to 1 on page 1).

1. button

Switch the unit between ON and STANDBY mode.

2. button

Select the source of audio (e.g. HDMI, USB, optical, etc)

3. button

Select Bluetooth mode. Press and hold to activate the

pairing function in Bluetooth mode or disconnect

the existing paired Bluetooth device.

4. button

Mute or resume the sound.

5. +/– buttons

Increase/decrease the volume level.

6. Remote Control Sensor

7. LED Indicator

Red: STANDBY

Green: AUX

Blue: Bluetooth

Yellow: Optical

Cyan: HDMI ARC

Purple: USB

8. Wall bracket screws

Inputs/outputs

(Refer to 2 on page 1).

1. OPTICAL

Opticial input jack.

2. HDMI ARC

Connect to a TV via HDMI cable (HDMI version 1.4 or higher).

3. USB

Insert USB ash drive to play music.

4. AUX

Connect to an external audio device.

5. AC~

Connect power cord.

Remote control

(Refer to 3 on page 1).

1. Switch the unit between ON and STANDBY mode.

2. Select Bluetooth mode.

Press and hold to activate the pairing function in Bluetooth mode

or disconnect the existing paired Bluetooth device.

3. Press repeatedly to select a signal source AUX, BT (Bluetooth),

OPT (Optical), ARC (HDMI) and USB mode.

4. +/– Increase/decrease the volume level.

5. / Skip to previous/next track in Bluetooth or USB mode.

6. Play/pause/resume playback in Bluetooth or USB mode.

7. Mute or resume the sound.

8. BASS +/– Adjust bass level. This only changes CUST EQ settings.

9. TRE +/– Adjust treble level. This only changes CUST EQ settings.

10. EQ Press repeatedly to switch between movie, music, voice, and

custom equaliser modes.

Remote control operation

The provided remote control allows the unit to be operated from a

distance.

• Even if the remote control is operated within the eective range

of 6m, remote control operation may be impossible if there are

obstacles between the unit and the remote control.

• If the remote control is operated near other products which

generate infrared rays, or if other remote control devices using

infra-red rays are used near the unit, it may operate incorrectly.

Conversely, the other products may operate incorrectly.

Battery installation

(Refer to 4 on page 1).

1. Press the battery compartment cover release clip in the direction

of the arrow and then pull the cover away from the remote.

2. Insert two AAA size batteries (included). Make sure the (+) and (–)

ends of the batteries match the (+) and (–) ends indicated in the

battery compartment.

3. Close the battery compartment cover ensuring the release clip is

secured.

First time installation

Placement and mounting

(Refer to 5 on page 1).

A: Normal placement (place Soundbar on level surface in front of the

TV). Attach the silicone feet to the bottom of the soundbar.

B: Wall mounting

Wall mounting

NOTE:

ū Installation must be carried out by qualied personnel only.

Incorrect assembly can result in severe personal injury and property

damage (if you intend to install this product yourself, you must

check for installations such as electrical wiring and plumbing that

may be buried inside the wall). It is the installer’s responsibility to

verify that the wall will safely support the total load of the unit and

wall brackets.

ū Additional tools (not included) are required for the installation.

ū Do not overtighten screws.

ū Keep this instruction manual for future reference.

ū Use an electronic stud nder to check the wall type before drilling

and mounting.

(Refer to 6 on page 1).

1. Drill 4 parallel holes (Ø 5.5~6 mm each according to wall type) in

the wall. The distance between the holes should be 708 mm.

Firmly x 1 plug into each hole in the wall.

2. Tighten the wall mount brackets on the wall with screws and

screwdriver (not included). Make sure the they are securely

installed.

3. Loosen the screws at the back of the unit for 2~3 mm.

4. Lift the unit onto the wall mount brackets and slot into place.

Connections

HDMI ARC input

(Refer to 7 on page 2).

The ARC (Audio Return Channel) function allows you to send audio

from your ARC- compliant TV to your sound bar through a single HDMI

connection. To enjoy the ARC function, please ensure your TV is both

HDMI-CEC and ARC compliant and set up accordingly. When correctly

set up, you can use your TV remote control to adjust the volume

output (+/– and ) of the sound bar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp HT-SB100 - Soundbar Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info