Bedienungsanleitung Sharp XV-Z17000 (Seite 74 von 81) (Englisch)

469881

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

Troubleshooting

Problem Check Page

No picture or projector does

not start

• Projector power cord is not plugged into the wall outlet. 23

• Power to the external connected devices is off. –

• The lens shutter is closed. 23, 28

• The selected input mode is wrong. 27, 41, 42

• Cables are incorrectly connected to the projector. 19-23

• Remote control battery has run out. 13

• External output has not been set when connecting notebook computer. –

• The lamp unit cover is not installed correctly. 63, 64

• The selected “Signal Type” is wrong. 41

•

The video signal format of the video equipment is not set correctly.

• “Bright” is set to minimum position. 37

Color is faded or poor.

• Image adjustments are incorrectly set. 37

(S-VIDEO or VIDEO input)

• Video input system is incorrectly set.

(COMPONENT, COMPUTER/COMPONENT or HDMI1, 2 input)

• Input signal type is incorrectly set.

Picture is blurred;

noise appears.

• Adjust the focus. 24

• The projection distance exceeds the focus range. 18

(Computer input)

• Perform “SIG-ADJ” Adjustments (“Clock” Adjustment)

• Perform “SIG-ADJ” Adjustments (“Phase” Adjustment)

• Noise may appear depending on the computer.

–

• The “DNR” (Digital Noise Reduction) or “MNR” (Mosquito Noise Reduc-

tion) setting is not correct.

• There is fog on the lens. If the projector is carried from a cold room into a

warm room, or if it is suddenly heated, condensation may form on the surface

of the lens and the image will become blurred. Please set up the projector at

least one hour before it is to be used. If condensation should form, remove the

power cord from the wall outlet and wait for it to clear.

–

An unusual sound is

occasionally heard

from the cabinet.

• If the picture is normal, the sound is due to cabinet shrinkage caused

by a room temperature changes. This will not affect operation or perfor-

mance.

–

Maintenance

indicator on the

projector illuminates.

• See “Maintenance Indicators”. 60

Picture is green when

receiving YPbPr

signals and the video

equipment is connected

to the COMPONENT or

COMPUTER/COMPONENT

terminal on the projector.

• Change the input signal type setting. 41

Picture is pink when receiv-

ing RGB signals and the video

equipment is connected to the

COMPONENT or COMPUTER/

COMPONENT terminal on the

projector.

The black levels of the

image show banding or

appear faded when HDMI1

or 2 is selected.

• Make adjustments that result in the best picture quality in the “Dynamic

Range” setting.

Picture is too bright and

whitish.

• Image adjustments are incorrectly set. 37

-72

XV-Z17000_E_US.indb 72XV-Z17000_E_US.indb 72 2010/12/17 11:16:502010/12/17 11:16:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XV-Z17000 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XV-Z17000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info