Bedienungsanleitung Sharp XV-Z17000 (Seite 75 von 81) (Englisch)

469881

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

Appendix

-73

Problem Check Page

The cooling fan

becomes noisy.

• When temperature inside the projector increases, the cooling fan runs

faster.

–

The lamp does not light up

even after the

projector turns on.

• The lamp indicator is illuminating in red.

Replace the lamp.

• The lens shutter is opened fully.

23, 60, 63

The lamp suddenly turns off

during projection.

The image sometimes

ﬂ ickers.

• Cables are incorrectly connected to the projector or the connected equip-

ment works improperly.

• If this happens frequently, replace the lamp.

19-22

The lamp needs much time

to turn on.

• The lamp will eventually need to be changed.

While the remaining lamp life draws to a close, replace the lamp.

Picture is dark.

One Touch Play is not

enabled.

• Non-Sharp Video Products are connected.

One Touch Play function may not work when the projector is connected

to non-Sharp Video Products.

• An HDMI cable is not used for connection between the projector and the

Sharp Video Products.

One Touch Play function is enabled when the projector is connected to

the Sharp Video Products with an HDMI cable.

• One Touch Play function of the projector is not set to “On”. 46

• CEC settings of connected Sharp Video Products or other CEC devices

are incorrect.

–

• One Touch Play is set to “Off” and disabled when the Economy mode is

set to “On”.

System Standby is not

enabled.

• Non-Sharp Video Products are connected.

System Standby function may not work when the projector is connected

to non-Sharp Video Products.

• An HDMI cable is not used for connection between the projector and the

Sharp Video Products.

System Standby function is enabled when the projector is connected to

the Sharp Video Products with an HDMI cable.

• System Standby function of the projector is not set to “On”. 46

• CEC settings of connected Sharp Video Products or other CEC devices

are incorrect.

–

A response code cannot be

received when the

projector was attempted

to be controlled using

RS-232C commands from

a computer during standby.

• In the case of transmitting RS-232C commands from a computer during

standby, it takes a maximum of 30 seconds for the computer to receive

the response code. Set the response code waiting time of the computer

to 30 seconds or more.

The remote control

cannot be used.

• Operate the remote control while pointing it at the projector’s remote

control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong ﬂ uorescent light is shining on the projector’s

remote control sensor, place the projector where it will not be affected by

strong light.

• The batteries may be depleted or inserted incorrectly. Make sure the bat-

teries are inserted correctly or insert new ones.

XV-Z17000_E_US.indb 73XV-Z17000_E_US.indb 73 2010/12/17 11:16:502010/12/17 11:16:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XV-Z17000 Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XV-Z17000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info