Bedienungsanleitung Siemens HB34D553 (Seite 20 von 32) (Englisch)

527327

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Replacing the cooking compartment bulb

Heat-resistant 230 V/25 W halogen bulbs with seals are

available from the after-sales service. Please specify the E

number and FD number of your appliance.

: Risk of burns!

Allow the cooking compartment and cooking compartment light

to cool before changing the bulb.

Always use a dry cloth to remove a new halogen bulb from the

packaging, otherwise it will not last as long.

1.Switch off the fuse in the fuse box or unplug at the mains.

2.Turn the cover anti-clockwise to remove.

3.Remove the bulb and replace with a bulb of the same type.

4.Slide the new seals and the clamping ring onto the glass

cover in the right order.

5.Screw the glass cover with the seals back on again.

6.Connect the appliance to the mains and reset the clock.

Never operate the appliance without the glass cover and seals.

Replacing the glass cover or seals

Any damaged glass cover or seals must be replaced. Please

provide the after-sales service with the E number and FD

number of your appliance.

Turning the temperature selector cancels

the cooking operation

A temperature outside of the possible tem-

perature range has been set

Check the temperature ranges for the

operating modes. Press the

† button

0 and ‹:‹‹ light up in the display

Power cut Reset the clock time (see section: "Time-

setting options")

”‰ is shown in the display

The automatic safety switch-off is active Press any button.

The

¯ indicator appears even though the

water tank is full

The water tank has not been pushed in

properly

Slide in the water tank until it engages

The detection system is not working Call the after-sales service

The

¯ indicator appears even though the

water tank is not yet empty, or the water

tank is empty but the

¯ indicator does not

appear

The water tank is dirty. The mobile water

level indicators are jammed

Shake and clean the water tank. If the

parts cannot be released, obtain a new

water tank from the after-sales service.

The water tank empties for no discernible

reason. The evaporator dish is overflowing

The water tank was not closed properly Close the lid until you feel it engage.

The tank cover seal is dirty Clean the seal

The seal in the tank cover is defective Obtain a new water tank from the after-

sales service

The evaporator dish has boiled dry even

though the water tank is full

The water tank has not been pushed in

properly

Slide in the water tank until it engages

The feed line is blocked Descale the appliance. Check whether the

water hardness is set correctly

The

¯ indicator appears

The appliance has not been used for at

least 2 days and the water tank is full

Empty and clean the water tank. Always

empty the water tank after cooking

There is a "pop" noise during cooking Cold/warm effect with frozen food, caused

by the steam

This is normal.

When you cook with steam, a lot of steam

is created

The appliance is being automatically cali-

brated

This is normal.

When cooking with steam, a lot of steam is

created again

The appliance is unable to calibrate itself

automatically if cooking times are too

short

Reset the appliance to the factory settings

(see Basic settings section). Then start

steaming at 100 °C for 20 minutes

Steam escapes from the ventilation slots

during cooking

This is normal.

The appliance is not producing steam

properly

Limescale has formed in the appliance Start descaling (see Section: Descaling)

Error message

“‹‚‚ appears in the dis-

play

A button was pressed for too long or is

jammed

Press the

0 button to clear the fault mes-

sage. Press each button and check that it

is clean

“... error message appears in the dis-

play

Technical fault.

Press the

0 button to delete the error

message. Reset the clock if required. If the

error message appears again, call the

after-sales service

The appliance is not heating. The colon

flashes in the display

A button combination was actuated Set the Steam operating mode to 35 °C,

then press and hold the

@ button until a

signal sounds. Press the

@ button again

briefly

Problem Possible cause Notes/remedy

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens HB34D553 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens HB34D553

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info