Bedienungsanleitung Siemens s40 (Seite 30 von 44) (Englisch)

230430

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Owner ID

You can store an owner ID in your

phone to be shown when you

switch on the phone. Select

»Define« to enter the necessary

information, which corresponds to

an address book entry.You can also

select an entry from your address

book or one of your phone books

to be stored as your owner ID.

Select »Show at power up« to

activate/deactivate the function.

When the function is activated

press »OWNER« during the power

up phase to see the contents of

your owner ID.

You can change an existing Owner

ID by selecting »Edit«.

The contents of the Owner ID

can be sent as a business card via

IrDA (see p. 33).

Facts & Tips

• If, by mistake, you select a language

which you do not understand, you can

always return to the original SIM card

language by pressing the following

keys: 0000 , in standby

mode.

• When you change the menu lan-

guage of your phone, it is advisable to

change the keypad language accord-

ingly.

• The owner ID is stored in the inter-

nal memory of the phone and will

thus not be shown in the display if

you use your SIM card in another

phone.

Setup menu

Phone setup

Setup menu

Enter the Setup menu

by pressing »MENU«

Select »Phone setup«

Language

Select »Language« to change the

menu language of your phone.

IrDA

Under »IrDA Nickname« you can

enter an ID name by which you

want other IrDA devices to identify

your mobile phone.

By selecting »Printer« and then

»Setup« you get the option to

define the protocol language of the

printer you want to use.

If you select »Test page«, a stan-

dard test page will automatically be

sent to the printer.

Backlight

To save your battery and thus

increase both conversation and

standby times you can choose to

have the backlight permanently

switched off.

Handsfree

(Car kit & headset)

This option is effective only if your

phone is connected to a handsfree

device. See specific user guides for

further information.

Greeting

Make a welcome greeting on your

phone according to your own wish-

es. Press »EDIT« and delete the old

greeting by holding down »CLEAR«.

Enter the new greeting via the key-

pad, and confirm by pressing »OK«.

(This function may not be available

on all networks).

Signal diode

The LED on the top of the phone

provides information about the fol-

lowing:

• Green flash

In contact with a network

• Fast green flash

Incoming call

• Very fast green flashes

New information, e.g.

a missed call or a new message.

• Red flash

No contact with a network

• Fast red flash

Low battery

Select individually whether you

want these indicators to be active

or not.

Graphics

This submenu allows you to

choose between different symbols

for the battery and the signal

strength indicators.

This is also where you adjust the

contrast of the display.

First

User guide S40 GB 01/03/02 10:42 Side 56

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens s40 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info