Bedienungsanleitung Skil 0280 (Seite 14 von 164) (Alle Sprachen)

797781

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

-press and rotate in the direction of the arrow P until

approx. 13 cm of line is left on both sides

• Remove line o

In case the cutting line fails to protrude from spool hole

! 

-press release buttons N to remove the spool cover

-remove the line from the spool

-align and press the spool cover until it snaps into place

-follow “Line replacement” instruction above

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• 

ensure that all moving parts have come to a complete

standstill

• Always keep tool clean (especially ventilation slots A 2)

-clean the tool with a damp cloth (do not use cleaning

agents or solvents)

-clean line cutting blade Q 2 and cutting guard G 2

after each use

-clean ventilation slots A 2 regularly with a brush or

compressed air

• Regularly check the condition of the cutting head and the

tightness of nuts, bolts and screws

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

-send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

• Be aware that damage due to overload or improper

handling of the product will be excluded from the

warranty (for the SKIL warranty conditions see

www.skil.com or ask your dealer)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! in case of electrical or mechanical malfunction,



Tool does not operate

-empty battery -> charge battery

-hot battery -> let battery cool down

-internal fault -> contact dealer/service station

Tool operates intermittently

-internal wiring defective -> contact dealer/service

station

-

Tool vibrates abnormally

-grass too high -> cut in stages

Tool does not cut

-

Line cannot be fed

-spool empty -> inspect spool; rewind if necessary

-line entangled inside spool -> inspect spool; rewind if

necessary



cutting blade

being switched on, when

-remove load and restart

-the 4 levels of the battery level



from the tool and charge the battery qc

-the battery temperature is not within the allowable



4 levels of the battery level indicator keep solid red for

10s; wait until battery has returned within the allowable

operating temperature range qd

! 



damaged

• Trimming

! ensure that the cutting area is free of stones,

debris and other foreign objects

! start trimming only when tool runs at full speed

-cut long grass in layers (always start from the top)

-only trim with the tip of the cutting line

-do not cut damp or wet grass

-prevent the cut grass from clogging the spool (do not

make heavy cuts)

-do not overload the tool

-carefully cut around trees and bushes, so that they do

not come into contact with the cutting line

-keep the tool away from solid objects in order to protect

the cutting line against excessive wear

-be aware of the kickback forces that occur when solid

objects are touched

• Holding and guiding the tool y

-for cutting long grass slowly swing the tool from right to

left and vice versa

-

control of the tool at all times

-maintain a stable working position

-always hold the tool well away from your body

• Line feeding u

-tap trimmer head lightly on a solid surface while the

motor is running

! tap trimmer head on bare ground or hard soil,

when tapping in tall grass, the motor may overheat

-

length by line cutting blade Q

! take care against injury from line cutting blade Q

-feed the lines regularly to maintain full cutting circle

-when the motor runs without load and no grass is cut,

the cutting line is stuck, worn or broken; rewind or

replace the line

• 

-

-press the trimmer head and pull the lines to feed the

line manually and check for proper installation

-after line feeding always return the tool to its normal

operating position before switching on

-when the motor runs without load and no grass is cut,

the cutting line is stuck, worn or broken; rewind or

replace the line

• Line replacement i

! 

-insert the 5m long cutting line into spool hole and push

until it protrudes from the other side

-pull the line until equal amounts of line appear on both

sides

Skil 0280 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info