Bedienungsanleitung Skil 0760 (Seite 7 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

480084

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

• Ensure that all current-conducting components in the

working area are protected against splashed water

• Keep cord connections dry and o ground

• Inspect the cord periodically and have it replaced by a

qualied person, if damaged

• Do not run over, crush or pull the (extension) cord

• Protect the (extension) cord from heat, oil and sharp

edges

• Only use an extension cord which is intended for outdoor

use and equipped with a watertight plug and coupling-

socket

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Only use extension cords with a maximum length of 20

metres (1,5 mm²) or 50 metres (2,5 mm²)

• Inspect the extension cord periodically and replace it, if

damaged (inadequate extension cords can be

dangerous)

• Never touch the mains plug with wet hands

• Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord

before disconnecting the plug)

• When connecting a new plug, pay attention to the

following (U.K. only):

- plugs and sockets conforming to BS 4243 or BS 196

should be used wherever practicable

- domestic pattern plugs to BS 1363 are not

recommended, but if their use is essential, those

which have barriers or moulded channels inside

should be selected, so that, if the earth continuity

conductor is pulled out of its terminal, it is unlikely to

be able to touch the phase terminal of the fuse carrier

- domestic pattern plugs to BS 546 should not be used

- the wiring of the plug should leave more slack in the

earth continuity conductor than in the other cores, so

that it is not the rst core to be pulled out of its

terminal, should the cord grip fail

- plugs which have good grips capable of maintaining a

rm hold on the cable sheath should be selected

- in general, additional means should be provided to

relieve stress on cable terminations in the plug (for

example, additional cable clamps should be tted or a

substantial chain could be used to tether the machine

to a xed point)

- plugs and sockets situated near the work site or

outdoors should be to class IP 55 of BS 5490 to

provide adequate protection against ingress of water,

etc. and cable entries require eective sealing

- rubber shrouds should be provided over cable glands

- drip-proof (class IP X2 of BS 5490) plugs and sockets

to BS 4343 are suitable for use indoors where the plug

is away from the water spray area where the appliance

is in use

USE

• Assembly instructions 6

- the sequence of the numbers appearing in the drawing

corresponds with the sequence of the steps to be

followed for assembling the high-pressure washer

- as a safety precaution press trigger lock A to avoid

that trigger B is activated accidentally

• Connection to water supply 7

- screw inlet connector C onto water inlet D

! never use inlet connector C without water filter E

- attach water supply hose (not supplied) to water tap

and inlet connector C

! ensure that the temperature of the incoming water

does not exceed 40°C (on a hot day run the water

until it cools down before connecting to water tap)

• Operating the tool 8

- ensure that the tool is placed on a solid base and in

vertical position

- connect the tool to the mains supply (ensure that

mains switch F is in the o-position)

- open water tap

- press trigger lock A to release trigger B

- fully press trigger B to release any trapped air from the

tool or the water supply hose

- release trigger B and press trigger lock A

- switch on the tool by pressing button “I” of mains

switch F

- after switching on the motor starts running for a few

seconds until maximum pressure is reached

- press trigger lock A, point spraying nozzle G at the

area to be washed and then pull trigger B

- switch between a concentrated jet of water and a wide

spray by turning nozzle G

- upon release of trigger B the motor stops running after

a few seconds when maximum pressure is reached

- switch o the tool by pressing button “O” of mains

switch F

- close water tap

- fully press trigger B until there is no more water

pressure in the tool

- after use press trigger lock A to avoid that trigger B is

activated accidentally

! disconnect plug from power source and ensure

that the cutting blade has stopped rotating

- disconnect water supply hose from tool and water tap

• Use of detergent bottle 9

! ensure that trigger is locked and mains switch is

in the off-position

- unscrew bottle H from detergent nozzle J and ll it with

biodegradable detergent suitable for high-pressure

washer application (the use of other detergents or

chemicals may adversely affect the safety of the tool)

! do not use undiluted detergents

- screw lled bottle H onto detergent nozzle J

- remove lance K from hand gun L and mount detergent

nozzle J instead as illustrated

- press trigger lock A, point detergent nozzle J at the

area to be washed and then pull trigger B

! detergent does not come out under high pressure

APPLICATION ADVICE

• When using detergent bottle H

! read the detergent label for additional

instructions

- always wet the object rst

- apply detergent to the object from the bottom up

- give the detergent time to work, but never leave it to dry

- rinse from top and work downwards

• For more tips see www.skileurope.com

Skil 0760 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info