Bedienungsanleitung Skil 0760 (Seite 8 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

480084

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Before maintenance always switch off tool, ensure

there is no water pressure in tool and hand gun,

disconnect plug from power source, and disconnect

tool from water supply

• Always keep tool and cord clean (especially ventilation

slots S 2)

- do not use water, solvents or polishes

- regularly clean spraying nozzle G using cleaning

needle M 0 (remove spray lance K from hand gun L

rst)

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

• Cleaning water lter

- remove water lter E 2 from inlet connector C 2 with

long nose pliers

- rinse it clean and put it back (replace it when

damaged)

! never use the tool with a damaged water filter

• Storage !

- store the tool out of reach of children in a location

where the ambient temperature will not exceed 40°C

or drop below 0°C

- do not place other objects on top of the tool

- securely mount storage rail N on the wall with 4

screws (not supplied) and horizontally leveled

- use storage rail N and storage straps P as illustrated

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switch off the tool and disconnect the plug before

investigating the problem

★ Spray is not consistent

- nozzle partly blocked -> clean nozzle

★ Motor does not start or stops suddenly

- power supply socket faulty -> use another socket

- plug not connected -> connect plug

- thermal protection switched o the motor -> let the tool

cool down for 5 minutes

★ Motor is running but spray is poor

- nozzle completely blocked -> clean nozzle

- water lter clogged -> clean water lter

- air in the pump -> ensure that water inlet connector is

securely tted

- inadequate water supply -> check that water tap is

fully open

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol @ will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this product

is in conformity with the following standards or

standardized documents: EN 60335, EN 61000,

EN 55014 in accordance with the provisions of the

directives 2006/95/EC, 2004/108/EC, 2006/42/EC,

2000/14/EC, 2011/65/EU

• Technical file at: SKIL Europe BV (PT-SEU/PJE),

4825 BD Breda, NL

ÊÆÇÎ¹Æ¼½ÊÄÇÇÌ

Á»½Ê½ËÁ¼½ÆÌ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

¹ÆÊÇÅÅ½Ä½Æ

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

13.10.2011

NOISE/VIBRATION

• Measured in accordance with EN 60704-1 the sound

pressure level of this tool is 81 dB(A) and the sound

power level 93 dB(A) (standard deviation: 2.2 dB), and

the vibration < 2.5 m/s² (hand-arm method; uncertainty

K = 1.5 m/s²)

• Measured in accordance with 2000/14/EC

(EN/ISO/5349) the guaranteed sound power level LWA is

lower than 97 dB(A)

• The vibration emission level has been measured in

accordance with a standardised test given in

EN/ISO/5349; it may be used to compare one tool with

another and as a preliminary assessment of exposure to

vibration when using the tool for the applications

mentioned

- using the tool for dierent applications, or with

dierent or poorly maintainted accessories, may

signicantly increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing your

work patterns

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0760 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info