Bedienungsanleitung Skoda Rapid - 2013 (Seite 180 von 218) (Englisch)

678345

180

Zoom out

Zoom in

Vorherige Seite

1/218

Nächste Seite

›

Switch off the engine.

›

Move the gearshift lever into Neutral or move the selector lever for the auto-

matic gearbox into position P.

›

Firmly apply the handbrake.

›

If a trailer is connected, uncouple it.

›

Remove the vehicle tool kit » page 176 and the spare wheel » page 172 from

the boot.



Changing a wheel

First read and observe the introductory information and safety warn-

ings on page 177.

›

Remove the full wheel trim » page 173 or caps » page 173.

›

First of all slacken the anti-theft wheel bolt and then the other wheel

bolts » page 178.

›

Jack up the vehicle until the wheel that needs changing is clear of the

ground » page 179.

›

Unscrew the wheel bolts and place them on a clean surface (cloth, paper, etc.).

›

Remove the wheel carefully.

›

Attach the spare wheel and slightly screw on the wheel bolts.

›

Lower the vehicle.

›

Alternately tighten wheel bolts opposite (diagonally) with the wheel wrench.

Tighten the anti-theft wheel bolt last » page 178.

›

Replace the wheel trim or the caps.

Note

■

All bolts must be clean and must turn easily.

■

Under no circumstances grease or oil the wheel bolts!

■

When fitting unidirectional tyres, ensure that the direction of rotation is cor-

rect » page 171.



Follow-up work

First read and observe the introductory information and safety warn-

ings on page 177.

The following steps must also be performed after changing the wheel.



›

Stow and attach the replaced wheel in the spare wheel well using a special

bolt » page 172, Spare wheel.

›

Stow the tool kit in the space provided and secure using the band.

›

Check the tyre pressure on the installed spare wheel as soon as possible.

›

Have the tightening torque of the wheel bolts checked with a torque wrench

as soon as possible.

›

Replace the damaged wheel or consult a specialist garage about repair options.

Note

■

If it is determined that the wheel bolts are corroded and difficult to turn when

changing the wheel, the bolts must be replaced before checking the tightening

torque.

■

Drive cautiously and only at a moderate speed until the tightening torque has

been checked.



Loosening/tightening wheel bolts

Fig. 148

Changing a wheel: Loosening

the wheel bolts

First read and observe the introductory information and safety warn-

ings

on page 177.

Loosening

›

Push the wheel wrench onto the wheel bolt up to the stop

›

Grasp the end of the wrench and turn the bolt about one turn in the direction of

the arrow » Fig. 148.

Tightening

›

Push the wheel wrench onto the wheel bolt up to the stop





Use the appropriate adapter for undoing and tightening the anti-theft wheel bolts » page 179.

178

Do-it-yourself

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skoda Rapid - 2013 Seite 180

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skoda Rapid - 2013

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info