Bedienungsanleitung Skoda Rapid - 2013 (Seite 185 von 218) (Englisch)

678345

185

Zoom out

Zoom in

Vorherige Seite

1/218

Nächste Seite

WARNING (Continued)

■

The non-insulated parts of the terminal clamps must never touch each other

– there is a risk of short circuit.

■

The jump-start cable connected to the positive terminal of the battery must

not come into contact with electrically conducting parts of the vehicle – there

is a risk of short circuit.

■

Do not clamp the jump-start cable to the negative terminal of the dis-

charged battery. There is the risk of detonating gas seeping out the battery

being ignited by the strong spark which results from the engine being started.

■

Route the jump-start cables so that they cannot be caught by any rotating

parts in the engine compartment.

■

Do not bend over the battery – there is a risk of caustic burns.

■

The vent screws of the battery cells must be tightened firmly.

■

Keep any sources of ignition (naked flame, lit cigarettes, etc.) away from the

battery – there is a risk of explosion.

■

Never jump-start vehicle batteries with insufficient acid levels – risk of ex-

plosion and chemical burns.

CAUTION

■

There must not be any contact between the two vehicles otherwise current

may flow as soon as the negative terminals are connected.

■

The discharged battery must be properly connected to the system of the vehi-

cle.

■

We recommend you buy jump-start cables from a car battery specialist.



Jump-starting using the battery from another vehicle

Fig. 153

Jump-starting: A – flat battery, B

– battery providing current

First read and observe the introductory information and safety warn-

ings on page 182.

The battery of another vehicle can be used to jump-start your vehicle if the en-

gine will not start because the battery is flat. Jump-start cables are required for

this purpose.

The jump-start cables must be attached in the following sequence.

›

Attach clamp

to the positive terminal of the discharged battery

» Fig. 153.

›

Attach clamp

to the positive terminal of the battery supplying power

›

Attach clamp

to the negative terminal of the battery supplying power

›

Attach the clamp

to a solid metal component firmly connected to the engine

block or to the engine block itself.

Starting engine

›

Start the engine on the vehicle providing the power and allow it to idle.

›

Start the engine of the vehicle with the discharged battery.

›

If the engine does not start, halt the attempt to start the engine after 10 sec-

onds and wait for 30 seconds before repeating the process.

›

Disconnect the cables in exactly the reverse order to the one described above.

Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the battery

supplying the power must not be significantly less than the capacity of the dis-

charged battery in your vehicle.

Jump-start cables

Only use jump-start cables which have an adequately large cross-section and in-

sulated terminal clamps. Observe the instructions of the jumper lead manufactur-

er.

Positive cable – colour coding in the majority of cases is red.

Negative cable – colour coding in the majority of cases is black.





183

Emergency equipment and self-help

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skoda Rapid - 2013 Seite 185

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skoda Rapid - 2013

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info